openwrt-mirror/openwrt
1
0
Fork 0
mirror of https://github.com/openwrt/openwrt.git synced 2025-12-21 17:04:28 +04:00
Code Issues Packages Projects Releases Wiki Activity

mediatek: filogic: add support Netcore NX30V2/N30PRO/POWER30AX/W7/GW3001

Browse Source 
Hardware specification:
  SoC: MediaTek MT7981B
  Flash: ESMT F50L1G41LB 128MB
  RAM: ESMT M15T2G16128A DDR3 256MB
  Ethernet: 3x 1G
  Button: Reset, WPS

MAC addresses
  LAN:	Label MAC (stored in Factory partition offset 0x1fef20)
  WAN:	LAN + 1
  WiFi:	LAN

Official LED layout, from left to right:
  [power] [internet] [wps] [wifi] [lan3/2/1] [wan]

Redefinition for OpenWrt:
  [power]: used for led-boot, led-failsafe, and led-running
  [internet]: used for WAN RX/TX indication
  [wps]: used for led-upgrade
  [wifi] and [lan3/2/1]: unchanged
  [wan]: used for WAN link indication

Installing OpenWrt:
  - Setup a tftp server on your PC. Copy
    xxx-preloader.bin, xxx-bl31-uboot.fip and
    xxx-initramfs.itb to tftp root directory.
  - Connect to the router via ssh or telnet,
    username: useradmin, password is the web
    login password of the router.
  - Backup all critical flash partitions with
    the following commands where x.x.x.x is
    the IP of your PC.

    IP=x.x.x.x
    cd /dev
    for d in /sys/class/mtd/mtd?; do
      if [ "$(cat $d/name)" = "BL2" ]; then
        tftp -l $(basename $d) -r bl2.img -p $IP
      elif [ "$(cat $d/name)" = "FIP" ]; then
        tftp -l $(basename $d) -r fip.bin -p $IP
      elif [ "$(cat $d/name)" = "Factory" ]; then
        tftp -l $(basename $d) -r factory.bin -p $IP
      fi
    done
    for d in /sys/devices/virtual/ubi/ubi0/ubi0_*; do
      [ "$(cat $d/name)" != "customer" ] && continue
      tftp -l $(basename $d) -r customer -p $IP
      break
    done

  - Flash with the following commands:

     cd /tmp
     tftp -r xxx-preloader.bin -g x.x.x.x
     tftp -r xxx-bl31-uboot.fip -g x.x.x.x
     mtd write xxx-preloader.bin spi0.0
     mtd write xxx-bl31-uboot.fip FIP
     mtd erase ubi

  - Set a static ip(192.168.1.254) for your PC.
    And then reboot the router. It will run
    initramfs image automatically.
  - After openwrt boots up, perform sysupgrade
    via web UI.

Reverting to the vendor firmware:
  - Setup a tftp server on your PC with ip
    address 192.168.1.254. And make sure
    bl2.img, fip.bin, factory.bin and customer
    are located in tftp root directory.
  - Power off the router.
  - Press and hold WPS key, then power on
    the router.
  - Release WPS key, when internet/wifi/wps
    leds are blinking.
  - Wait until internet/wifi/wps leds light
    up, power off the router.
  - Press and hold reset key, power up the
    router, release reset key 15s later.
  - Connect to http://192.168.1.1, now you
    can upload vendor .bin firmware.

Uboot netconsole:
  Uboot netconsole can be enabled by WPS
  or reset key.

  - Setup a linux PC with ip 192.168.1.254.
    Open a new terminal and execute
    'stty -isig -echo cbreak; nc -lup 6666'
  - Press and hold WPS(or reset) key, then
    power on the router.
  - Release key once internet/wifi/wps leds
    are all on.
    NOTE: don't hold the key more than 5s
    after internet/wifi/wps leds on, or it
    will try to revert to vendor firmware.
  - 5s later, uboot bootmenu will show on
    the terminal.

Signed-off-by: Zhiwei Cao <bfdeh@126.com>
Link: https://github.com/openwrt/openwrt/pull/18631
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Zhiwei Cao
2025-04-25 11:03:56 +08:00
committed by Hauke Mehrtens
parent b182f2e0b4
commit 344bb7f916
9 changed files with 706 additions and 0 deletions
Download Patch File Download Diff File Expand all files Collapse all files

201
target/linux/mediatek/dts/mt7981b-netis-common.dtsi Normal file
View File

@@ -0,0 +1,201 @@
// SPDX-License-Identifier: (GPL-2.0 OR MIT)
/dts-v1/;
#include "mt7981b.dtsi"
/ {
aliases {
serial0 = &uart0;
};
chosen {
stdout-path = "serial0:115200n8";
rootdisk = <&ubi_rootdisk>;
};
memory@40000000 {
reg = <0 0x40000000 0 0x20000000>;
device_type = "memory";
};
gpio-keys {
compatible = "gpio-keys";
reset {
label = "reset";
linux,code = <KEY_RESTART>;
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
};
wps {
label = "wps";
linux,code = <KEY_WPS_BUTTON>;
gpios = <&pio 0 GPIO_ACTIVE_HIGH>;
};
};
};
&eth {
status = "okay";
gmac0: mac@0 {
compatible = "mediatek,eth-mac";
reg = <0>;
phy-mode = "2500base-x";
nvmem-cells = <&macaddr_lan>;
nvmem-cell-names = "mac-address";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
mac@1 {
compatible = "mediatek,eth-mac";
reg = <1>;
phy-mode = "gmii";
phy-handle = <&int_gbe_phy>;
nvmem-cells = <&macaddr_wan>;
nvmem-cell-names = "mac-address";
};
};
&mdio_bus {
switch: switch@1f {
compatible = "mediatek,mt7531";
reg = <31>;
interrupt-controller;
#interrupt-cells = <1>;
interrupt-parent = <&pio>;
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
};
};
&crypto {
status = "okay";
};
&pio {
spi0_flash_pins: spi0-pins {
mux {
function = "spi";
groups = "spi0", "spi0_wp_hold";
};
conf-pu {
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
drive-strength = <MTK_DRIVE_8mA>;
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
};
conf-pd {
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
drive-strength = <MTK_DRIVE_8mA>;
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
};
};
};
&spi0 {
pinctrl-names = "default";
pinctrl-0 = <&spi0_flash_pins>;
status = "okay";
spi_nand@0 {
compatible = "spi-nand";
reg = <0>;
spi-max-frequency = <52000000>;
spi-tx-bus-width = <4>;
spi-rx-bus-width = <4>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "BL2";
reg = <0x0 0x100000>;
};
partition@100000 {
label = "u-boot-env";
reg = <0x100000 0x80000>;
};
partition@180000 {
label = "Factory";
reg = <0x180000 0x200000>;
nvmem-layout {
compatible = "fixed-layout";
#address-cells = <1>;
#size-cells = <1>;
eeprom_factory_0: eeprom@0 {
reg = <0x0 0x1000>;
};
macaddr_lan: macaddr@1fef20 {
reg = <0x1fef20 0x6>;
};
macaddr_wan: macaddr@1fef26 {
reg = <0x1fef26 0x6>;
};
};
};
partition@380000 {
label = "FIP";
reg = <0x380000 0x200000>;
};
partition@580000 {
label = "ubi";
reg = <0x580000 0x7280000>;
compatible = "linux,ubi";
volumes {
ubi_rootdisk: ubi-volume-fit {
volname = "fit";
};
};
};
};
};
};
&switch {
ports {
#address-cells = <1>;
#size-cells = <0>;
port@6 {
reg = <6>;
ethernet = <&gmac0>;
phy-mode = "2500base-x";
fixed-link {
speed = <2500>;
full-duplex;
pause;
};
};
};
};
&uart0 {
status = "okay";
};
&watchdog {
status = "okay";
};
&wifi {
status = "okay";
nvmem-cells = <&eeprom_factory_0>;
nvmem-cell-names = "eeprom";
};

64
target/linux/mediatek/dts/mt7981b-netis-nx30v2.dts Normal file
View File

@@ -0,0 +1,64 @@
/* SPDX-License-Identifier: (GPL-2.0-only OR MIT) */
/dts-v1/;
#include "mt7981b-netis-common.dtsi"
/ {
compatible = "netis,nx30v2", "mediatek,mt7981";
aliases {
label-mac-device = &gmac0;
led-boot = &led_power;
led-failsafe = &led_power;
led-running = &led_power;
led-upgrade = &led_wps;
};
leds {
compatible = "gpio-leds";
led_power: power {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_POWER;
gpios = <&pio 4 GPIO_ACTIVE_LOW>;
default-state = "on";
};
internet {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_WAN_ONLINE;
gpios = <&pio 7 GPIO_ACTIVE_LOW>;
};
led_wps: wps {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_WPS;
gpios = <&pio 5 GPIO_ACTIVE_LOW>;
};
wan {
color = <LED_COLOR_ID_BLUE>;
function = LED_FUNCTION_WAN;
gpios = <&pio 8 GPIO_ACTIVE_LOW>;
};
};
};
&switch {
ports {
port@0 {
reg = <1>;
label = "lan1";
};
port@1 {
reg = <2>;
label = "lan2";
};
port@2 {
reg = <3>;
label = "lan3";
};
};
};

4
target/linux/mediatek/filogic/base-files/etc/board.d/01_leds
View File

@@ -151,6 +151,10 @@ netgear,eax17)
netgear,wax220)
ucidef_set_led_netdev "eth0" "LAN" "green:lan" "eth0"
;;
netis,nx30v2)
ucidef_set_led_netdev "wanlink" "WANLINK" "blue:wan" "eth1" "link"
ucidef_set_led_netdev "wanact" "WANACT" "blue:wan-online" "eth1" "tx rx"
;;
netis,nx31)
ucidef_set_led_netdev "wan" "wan" "blue:wan" "eth1" "link tx rx"
;;

1
target/linux/mediatek/filogic/base-files/etc/board.d/02_network
View File

@@ -14,6 +14,7 @@ mediatek_setup_interfaces()
h3c,magic-nx30-pro|\
imou,hx21|\
konka,komi-a31|\
netis,nx30v2|\
netis,nx31|\
nokia,ea0326gmp|\
mercusys,mr80x-v3|\

1
target/linux/mediatek/filogic/base-files/lib/upgrade/platform.sh
View File

@@ -100,6 +100,7 @@ platform_do_upgrade() {
mediatek,mt7981-rfb|\
mediatek,mt7988a-rfb|\
mercusys,mr90x-v1-ubi|\
netis,nx30v2|\
netis,nx31|\
nokia,ea0326gmp|\
openwrt,one|\

31
target/linux/mediatek/image/filogic.mk
View File

@@ -2140,6 +2140,37 @@ define Device/netgear_wax220
endef
TARGET_DEVICES += netgear_wax220
define Device/netis_nx30v2
DEVICE_VENDOR := Netis
DEVICE_MODEL := NX30V2
DEVICE_ALT0_VENDOR := Netcore
DEVICE_ALT0_MODEL := POWER30AX
DEVICE_ALT1_VENDOR := Netcore
DEVICE_ALT1_MODEL := N30PRO
DEVICE_ALT2_VENDOR := GWBN
DEVICE_ALT2_MODEL := GW3001
DEVICE_ALT3_VENDOR := GLC
DEVICE_ALT3_MODEL := W7
DEVICE_DTS := mt7981b-netis-nx30v2
DEVICE_DTS_DIR := ../dts
DEVICE_DTC_FLAGS := --pad 4096
DEVICE_DTS_LOADADDR := 0x43f00000
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware
KERNEL_LOADADDR := 0x44000000
KERNEL := kernel-bin | gzip
KERNEL_INITRAMFS := kernel-bin | lzma | fit lzma $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb with-initrd | pad-to 64k
KERNEL_INITRAMFS_SUFFIX := .itb
KERNEL_IN_UBI := 1
UBOOTENV_IN_UBI := 1
IMAGES := sysupgrade.itb
IMAGE_SIZE := 117248k
IMAGE/sysupgrade.itb := append-kernel | fit gzip $$(KDIR)/image-$$(firstword $$(DEVICE_DTS)).dtb external-with-rootfs | pad-rootfs | append-metadata
ARTIFACTS := spim-nand-preloader.bin spim-nand-bl31-uboot.fip
ARTIFACT/spim-nand-preloader.bin := mt7981-bl2 spim-nand-ddr3
ARTIFACT/spim-nand-bl31-uboot.fip := mt7981-bl31-uboot netis_nx30v2
endef
TARGET_DEVICES += netis_nx30v2
define Device/netis_nx31
DEVICE_VENDOR := netis
DEVICE_MODEL := NX31