cortexa72 enables ext4 for its eMMC and SD card devices, so the UBI
images of the MikroTik RB5009 are built for ext4 as well. An ext4 file
system in a UBI volume can only be used read-only through ubiblock, so
these images are of no use.
They are broken anyway: the ext4 images are gzipped as a whole, which
moves the metadata of the sysupgrade image into the gzip stream. fwtool
reads the metadata from the end of the file, so sysupgrade rejects the
image with "Image metadata not present".
Build the UBI images for squashfs only.
Link: https://github.com/openwrt/openwrt/pull/25658
Signed-off-by: Paul Spooren <mail@aparcar.org>
Add kmod-usb-storage-uas to the default package set for the Turris
Omnia and Turris MOX.
Both devices provide USB host ports that can be used with fast USB
storage devices such as SSDs. UAS provides a more efficient transport
than the legacy USB Mass Storage Bulk-Only Transport and allows such
devices to better utilize the available USB bandwidth.
Without the UAS driver installed, compatible devices silently fall
back to the legacy transport, which can limit storage performance.
Users may not realize that kmod-usb-storage-uas needs to be installed
separately.
The package is only about 10 KiB and remains a loadable kernel module,
so users can remove it independently if a particular USB storage
device has compatibility issues.
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/24742
Signed-off-by: Robert Marko <robimarko@gmail.com>
Armada 3700 COMPHY nodes with #phy-cells = <1> supply only the port
argument. The translator nevertheless reads args[1] for TX and RX
polarity, although the phandle parser initializes only supplied cells.
This can program unintended SerDes polarity from uninitialized stack
data.
Add a kernel 6.18 patch that defaults both inversion flags to false
when the optional polarity argument is absent, while preserving
polarity selection for two-cell references.
Tested on CZ.NIC Turris MOX with a Peridot switch using Linux 6.18.54.
The patch restores 2500BASE-X communication without CRC errors. Cold
boots, reboots and interface down/up cycles also pass.
Closes#24069
Signed-off-by: Štěpán Dalecký <daleckystepan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/25518
Signed-off-by: Robert Marko <robimarko@gmail.com>
Armada 38x uses Cortex-A9 r4p1, but the current kernel config selects
erratum 720789, which was fixed in r2p0, and omits some errata that
still affect r4p1. Fix the config.
Signed-off-by: Qingfang Deng <dqfext@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/25297
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport a series of upstream patches for the adt7470 hwmon driver,
accepted for kernel v7.3. It exposes the fan control lines via the
generic PWM framework and thermal zone sensors.
Instead of relying on userland scripts, the kernel can now control
the fan speed directly through standard cooling maps and PWM fans
configured in the DTS. Currently in the tree, only edgecore_ecs4100-12ph
seems to use this chip.
Signed-off-by: Luiz Angelo Daros de Luca <luizluca@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/24803
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The MikroTik RB5009UPr+S+IN is a multigig router based on the Marvell
Armada 7040 SoC, sharing the same hardware base as the RB5009UG+S+IN
with added PoE-out support on all ethernet ports.
Specification:
- SoC : Marvell Armada 7040 (88F7040), 4x Cortex-A72
- CPU frequency : 350-1400 MHz
- RAM : 1 GB
- Flash : 16 MB SPI NOR + 1 GB NAND
- Switch : Marvell MV88E6393X
- Ethernet : 1x 2.5G (p1, QCA8081), 7x 1G (p2-p8), 1x SFP+ 10G
- PoE-in : 802.3af/at on p1, 24-57V
- PoE-out : 802.3af/at on p1-p8, 130 W total
- Power : DC jack / 2-pin terminal / PoE-in, 24-57V
- USB : 1x USB 3.0 type A, max 1.5 A
- LEDs/Keys (GPIO): 4x/1x
- UART : MikroTik SPI/UART combo header (10-pin, 2.0mm pitch)
- assignment : GND Vcc Rx ? GND / CLK DO /CS Tx DI (top view)
- settings : 115200n8
Flash instruction using initramfs image:
RouterBOOT cannot boot the OpenWrt kernel directly. A U-Boot loader
(u-boot.elf) is installed as an intermediary: RouterBOOT loads
u-boot.elf, which then loads the OpenWrt initramfs image.
1. Rename the downloaded initramfs image, removing the version number,
to: openwrt-mvebu-cortexa72-mikrotik_rb5009-initramfs-uImage.itb
2. Set up a BOOTP/TFTP server serving u-boot.elf, with the renamed
initramfs image in the same directory
3. Power off the router, hold the reset button (front panel), power on
and keep holding until the initramfs image has been served, then
release
4. The router boots the initramfs image, reachable at 192.168.1.1
5. Log in via SSH, install U-Boot, wipe NAND and flash OpenWrt:
. /lib/functions.sh
yafut -d /dev/mtd$(find_mtd_index "YAFFS") -w -i /tmp/u-boot.elf -o kernel -T
ubiformat /dev/mtd$(find_mtd_index "ubi") -y
sysupgrade /tmp/openwrt-mvebu-cortexa72-mikrotik_rb5009upr-squashfs-sysupgrade.bin
Recovery:
Hold the reset button while U-Boot is booting to load the initramfs
image again. To return to RouterOS, use MikroTik Netinstall.
MAC Addresses:
MAC addresses are read from the RouterBOOT hard_config in NOR via the
macaddr_hard nvmem cell:
offset +0 p1 (2.5G, label-mac-device)
offset +1 p2
offset +2 p3
offset +3 p4
offset +4 p5
offset +5 p6
offset +6 p7
offset +7 p8
offset +8 sfp
Tested-by: Sm00shed <sm00shed@posteo.de> (RB5009UPr+S+IN, OpenWrt v25.12.4,
kernel 6.12.87, mtpoe fw 65.21)
Signed-off-by: Przemek Rudy <prudy@protonmail.com>
[carlo@common-net.org: refactor RB5009UPr+S+IN support and fix sysupgrade path]
Signed-off-by: Carlo Filippi <carlo@common-net.org>
[sm00shed@posteo.de: fix compatible indentation, remove mikrotik,rb5009, expand commit message]
Signed-off-by: Sm00shed <sm00shed@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/23698
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Specialize RB5009UG model from generic RB5009.
Signed-off-by: Przemek Rudy <prudy@protonmail.com>
[carlo@common-net.org: fixed model name and backward compatibility ]
Signed-off-by: Carlo Filippi <carlo@common-net.org>
Signed-off-by: Sm00shed <sm00shed@posteo.de>
Link: https://github.com/openwrt/openwrt/pull/23698
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
-----
Hardware:
CPU: ARMADA 380 1x1332Mhz
RAM: 512MB DDR3
FLASH: 256MB MX30LF2G18AC
2x SATA III
2x USB3.0
1x USB2.0
i2c to control various states.
RTC with battery
1Gbit LAN (WoL capable)
9x LED
RESET button at back
Power button at front (gpio-poweroff)
Copy button at front
-----
Doesn't work
FAN control
buzzer
-----
UART connections
Connect UART to port J3 115200
+----+----+----+----+----+
|3.3V| TX | RX | | GND|
+----+----+----+ +----+
Depend of UART adapter board can fail to boot when adapter is attached. (all leds are dimmed) .
In that case disconnect UART for an < second and after that all leds should be white.
Stop u-boot by ctrl-c within 3s window. (bootdelay 7s or more helps)
setenv bootdelay 7
saveenv
-----
Instalation via UART
Boot initramfs-kernel.bin
setenv ethact egiga0
setenv serverip 192.168.1.11
setenv ipaddr 192.168.1.12
tftpboot 0x02000000 *initramfs-kernel.bin
bootm 0x02000000 -
Device is DHCP client by default ( as the other supported NAS)
do backup into safe space
/dev/mtd3 Kernel-1
/dev/mtd4 RootFS-1
use sysupgrade in console or via luci
-----
MAC addresses
mac stored in u-boot-env ethaddr
label mac = eth0 mac = 5c:6a:80:xx:xx:xx
-----
Setting up u-boot dual boot
u-boot contain two banks contain two OEM copies
To boot OpenWrt from bank1
setenv next_bootfrom 1
saveenv
To boot OEM from bank2
setenv next_bootfrom 2
saveenv
-----
Configuration via i2c
install i2c-tools
Enable WoL
i2cset -y 0x0 0xa 0xa 0x0006 w
Disable WoL
i2cset -y 0x0 0xa 0xa 0x0306 w
Enable auto power on
i2cset -y 0x0 0x0a 0x0a 0x0107 w
Disable auto power on
i2cset -y 0x0 0x0a 0x0a 0x0007 w
Signed-off-by: Robert Senderek <robert.senderek@10g.pl>
Link: https://github.com/openwrt/openwrt/pull/23228
Signed-off-by: Robert Marko <robimarko@gmail.com>
Newer kernels support applying sysctl keys from the kernel
command line.
Set sysctl.kernel.firmware_config.force_sysfs_fallback=0 in
MOX bootargs to disable firmware sysfs fallback without a
board-specific init script.
Signed-off-by: Štěpán Dalecký <daleckystepan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23666
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Turris MOX still upgrades from a legacy SD card image rather than
using the default sysupgrade path for cortexa53 devices.
Route image validation, upgrade handling and config backup through
the legacy_sdcard helpers so sysupgrade writes the correct image
format and preserves settings.
Signed-off-by: Štěpán Dalecký <daleckystepan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23666
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current code assumes that the rootfs_data UBI volume is on the same MTD
partition as the rootfs.
Unfortunately, this does not work on the Aruba AP-325 (and variants), since
the bootloader enforces a particular UBI volume layout.
Therefore, this adds a separate variable to set the rootfs_data partition,
and updates all existing devices with a non-default rootfs partition to also
specify the new variable.
Signed-off-by: Lukas Stockner <lukas@lukasstockner.de>
Link: https://github.com/openwrt/openwrt/pull/20738
Signed-off-by: Paul Spooren <mail@aparcar.org>
The current code assumes that the rootfs_data UBI volume is on the same MTD
partition as the rootfs.
Unfortunately, this does not work on the Aruba AP-325 (and variants), since
the bootloader enforces a particular UBI volume layout.
Therefore, this adds a separate variable to set the rootfs_data partition,
and updates all existing devices with a non-default rootfs partition to also
specify the new variable.
Signed-off-by: Lukas Stockner <lukas@lukasstockner.de>
Link: https://github.com/openwrt/openwrt/pull/20738
Signed-off-by: Test Dev <dev@example.org>
Currently, sysupgrade will only upgrade the unused slot, however since the
whole dual firmware logic is in the bootscript U-boot will just use the
first bootscript it finds.
So, in a case that you are running slot A it will upgrade slot B, however
that means that slot B will be still booted by the old bootscript that came
with the previous firmware version.
This is an issue if you need to change anything, so lets add a custom
function that upgrades the active bootscript as well after flashing the
slot firmware.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Methode uDPU and eDPU devices are one of the rare ones with a completely
custom image format being used with custom partition table with F2FS.
Instead of converting the boards to dual firmware (A/B style) and further
expand the already convoluted custom scripts, especially considering that
dual firmware conversion is a breaking change anyway, lets convert to using
the generic eMMC sysupgrade based images.
F2FS ZSTD compression is preserved thanks to fstools now supporting its use
on overlays.
Dual firmware support is implemented via U-Boot scripts so no U-Boot
upgrade is required.
Since there is a partition table layout change, eMMC must be wiped and
reflashed with the generated GPT image from OpenWrt initramfs.
Then on each sysupgrade the firmware slot will be altered.
Instructions:
1. Boot into OpenWrt initramfs
2. Copy openwrt-mvebu-cortexa53-methode_edpu-squashfs-emmc-gpt.img.gz to
the device into /tmp
3. Erase eMMC:
dd if=/dev/zero of=/dev/mmcblk0 bs=1M
4. Extract image
gzip -d /tmp/openwrt-mvebu-cortexa53-methode_edpu-squashfs-emmc-gpt.img.gz
5. Flash image
dd if=/tmp/openwrt-mvebu-cortexa53-methode_edpu-squashfs-emmc-gpt.img of=/dev/mmcblk0
6. Reboot
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Turris Mox boards may include an SDIO Wi-Fi module based on the
Marvell 88W8997 chip. Add kmod-mwifiex-sdio to the default package
list so the driver is included in the image out of the box.
Signed-off-by: Štěpán Dalecký <daleckystepan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23421
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The bootscript had several issues that prevented squashfs from booting:
- bootpath was set to "/" causing double slashes in load paths (e.g.
"//Image"); changed to "" so "${bootpath}/Image" resolves to "/Image"
- rootflags was set to "commit=5" (a btrfs-specific mount option) for
the ext4/squashfs case; cleared to empty string
- rootfstype was missing in the non-btrfs branch; added "auto" to let
the kernel detect the filesystem; the btrfs branch now sets "btrfs"
explicitly
- bootargs incorrectly referenced ${bootfstype} (the distroboot input
variable) instead of the locally constructed ${rootfstype}
- has_dtb assignment used shell-style "has_dtb=1" but was cleared with
"setenv has_dtb 0"; unified both to use setenv
- DTB load failure message now includes the attempted file path
- Fixed Image.lzma error echo that still used a stale "${subvol}/boot/"
prefix; now consistently uses ${bootpath}
- Removed undefined variable "rootpart" from env delete
Signed-off-by: Štěpán Dalecký <daleckystepan@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23421
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
With Kernel 6.18 the kernel size exceeds 4MB. Without additional changes
to the partition layout or kernel size reduction, the image will not be
usable. Disable this sub-target until necessary changes or a decision
regarding its removal have been made.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/22761
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Without explicit dependency between these two packages compilation
against Kernel 6.18 fails with the following error:
Package kmod-leds-turris-omnia is missing dependencies for the
following libraries: turris-omnia-mcu.ko
Make the dependency explicit to resolve this issue.
Signed-off-by: Stefan Kalscheuer <stefan@stklcode.de>
Link: https://github.com/openwrt/openwrt/pull/22761
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Spooren
Josef Schlehofer
John Audia
Štěpán Dalecký
Edoardo Pinci
Qingfang Deng
Luiz Angelo Daros de Luca
Shiji Yang
Rosen Penev
Tomáš Macholda
Przemek Rudy
Yanase Yuki
Robert Senderek
Lukas Stockner
Aleksander Jan Bajkowski
Robert Marko
Stefan Kalscheuer
Sven Friedmann
Jonas Jelonek