Remove KCONFIG symbols that no longer exist in kernel 6.18 from the kmod
definitions. Some were renamed and the new symbol is already listed in
the same package (e.g. CRYPTO_GF128MUL -> CRYPTO_LIB_GF128MUL,
USB_YEALINK -> INPUT_YEALINK, MEDIA_RC_SUPPORT -> RC_CORE). The others
belong to options and drivers that were removed upstream (e.g. CAN_LEDS,
E1000_NAPI, NF_FLOW_TABLE_HW, the Keyspan firmware options).
The generated package metadata is unchanged apart from the
Kernel-Config field of the affected packages.
Signed-off-by: Sander van Deijck <sander@vandeijck.com>
Link: https://github.com/openwrt/openwrt/pull/25965
Signed-off-by: Robert Marko <robimarko@gmail.com>
legacy_sdcard_do_upgrade needs partx after a full image write, but only
some targets listed it in DEFAULT_PACKAGES, where it could be deselected.
Select it from the feature and add it to DEFAULT_PACKAGES for the
ImageBuilder, which also covers qoriq, sifiveu and mvebu/cortexa9.
Signed-off-by: John Audia <therealgraysky@proton.me>
Share the partition layout check and disk write with the other
whole-disk image targets, which keeps user partitions from being erased.
The bootloader write is dropped; it lacked /dev/ and never hit the disk.
Signed-off-by: John Audia <therealgraysky@proton.me>
The Allwinner H5 uses the H3 R-PIO controller in addition to its
H5-specific main PIO controller. Moving the pinctrl configuration to
the subtargets left PINCTRL_SUN8I_H3_R disabled for cortexa53.
On the NanoPi NEO 2, usb0-vbus depends on the R-PIO PL2 GPIO. Without
the driver, the regulator and USB PHY remain deferred, preventing the
USB host controllers from probing. No USB device nodes are created
and lsusb reports "unable to initialize libusb: -99".
Enable PINCTRL_SUN8I_H3_R in the cortexa53 configuration to restore
the R-PIO driver required by H5 boards.
Fixes: 920fa6f061 ("sunxi: enable pinctrl driver in subtarget")
Signed-off-by: Joseph Chen <phenomenon0102@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/25588
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Both features describe an SoC family, which is the wrong granularity: a
mediatek/mt7623 board claims a display while a filogic board with a MIPI
DBI panel cannot, and rockchip claims audio for a NanoPi R2S as much as
for a Rock 5B. The audio-support and video-support packages carry that
information per image, and the modules depend on them.
Drop both features from every target that declares them.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The display target feature gates every DRM module, but it says nothing
useful: it is set on ten targets, so a mediatek/mt7623 board can have a
display while a filogic board with a MIPI DBI panel cannot, and rockchip
claims it for a NanoPi R2S as much as for a Rock 5B. Whether a board
drives a panel is a per-device choice, not a property of the SoC family.
The DRM and V4L2 nodes also end up 0600 root:root, so a display server
runs as root or not at all.
Add a video-support package which allocates the video and video-capture
groups and installs the hotplug rules for the DRM and V4L2 nodes, and
make the modules depend on it. The dependency is a plain one, not a
select, so the modules are offered once the feature is chosen. Targets
whose display drivers are built into the kernel carry the package in
DEFAULT_PACKAGES, since no module pulls it in for them, and the one
device profile that ships a DRM module on another target lists it
directly. DISPLAY_SUPPORT stays for now, so this changes no existing
selection.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The audio group and the rule that puts the ALSA character devices in it
are part of procd and base-files, so every image carries them whether or
not it has a sound card, and a package wanting the group has nothing to
depend on. Playback, capture and MIDI all land in one group as well, so a
process allowed to play is also allowed to record.
Move the lot into a new audio-support package with three groups, audio,
audio-capture and midi, and a hotplug fragment that sorts the sound nodes
between them. kmod-sound-core depends on the package, and so do the image
profiles that ship a sound driver. The dependency is a plain one, not a
select, so sound support is offered once the feature is chosen; userspace
that needs one of the groups depends on the same package. Images without
it fall back to the generic rule and get /dev/snd/* as 0600 root:root.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The Allwinner T113-s3 (sun8i) SoC features a dual-core Cortex-A7 ARM CPU and
128MB of DDR3 memory in the same physical package. It supports industrial
temperature ranges. Most of the IP blocks are shared with the D1/D1s core.
There are multiple variants of the SoC, which may vary in the included memory
size, with some of them including a C906 RISC-V co-processor.
Boards supported:
- MangoPi MQDual T113
- wireless-only (RTL8723DS)
- MYIR MYD-YT113 eMMC
- 1Gbit ethernet (Motorcomm YT8531 PHY)
- 4GByte eMMC
- M.2-type slot for 4G/5G cards, plus 2x SIM slot
- USB 2.0 ports
- GPIO/I2C/SPI/CAN ports
- FNLink 6131 (rtl8733bu) wifi module
- MYIR MYD-YT113 SPI
- Same as above but with 256Mbyte SPI-NAND flash instead of eMMC
- Rongpin RP-T113
- 100Mbit ethernet (ICplus IP101GR PHY)
- miniPCIe slot for 4G cards, plus 1x SIM slot
- 3x USB 2.0 ports
- RTL8723BS wireless
- HYM8563 RTC
- GPIO/I2C/SPI/CAN ports
- Olimex T113-Olinuxino
- 100Mbit ethernet (ICplus IP101GR)
- UEXT connector (GPIO/I2C/SPI ports)
- 1x USB 2.0
- audio jack, LEDC
Installation:
Use the standard sunxi installation to an SD-card.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Following up with errors reported in the ASU repo, these bananapi cases
do not match the DT compatible "bpi", sync with dts sources.
Also some profiles were overwriting SUPPORTED_DEVICES.
Sysupgrade would be failing in SUPPORTED_DEVICES check since
the DT compatible(/tmp/sysinfo/board_name) is not in SUPPORTED_DEVICES.
This should also fix errors when using ASU sysupgrade clients.
- Sync profile makefile target names with DT compatibles.
- Fix overwrites of SUPPORTED_DEVICES instead of appending.
- Adapt the uboot-sunxi profiles accordingly.
*bpi-p2-zero dts is still not upstream.
V2:
- Include fixes for arm926ejs(ARM926EJ-S) subtarget (LicheePi Nano and
PopStick v1.1) (profile rename for correct default SUPPORTED_DEVICES)
Fixes: https://forum.openwrt.org/t/luci-attended-sysupgrade-support-thread/230552/246
Fixes: https://github.com/openwrt/asu/issues/486
Fixes: https://github.com/openwrt/asu/issues/524
Fixes: 9aa66b8ce7 "sunxi: add support for Banana Pi M2 Berry"
Fixes: d5f615bf2a "sunxi: add support for Sinovoip Banana Pi M2 Plus"
Fixes: 3819c1638a "sunxi: Add support for Banana Pi M2 Ultra"
Fixes: 6bf8193b25 "sunxi: add support for Bananapi P2 Zero"
Fixes: 80edfaf675 "sunxi: add support for Banana Pi M3"
Fixes: 3c24a1d423 "sunxi: add support for NanoPi NEO Plus2 board"
Fixes: a689307c97 "sunxi: build image/uboot for the NanoPi NEO2"
Fixes: fde68cb809 "sunxi: add support for FriendlyARM NanoPi R1S H5"
Fixes: 3ec468ff4f "sunxi: add F1C100 (arm926ej-s) support"
Signed-off-by: Mario Andrés Pérez <mapb_@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/21095
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The cortexa53 target currently uses cpu erratums for Cortex-A510,
Cortex-A710, and Neoverse-N2. Remove them and enable cpu erratums
for Cortex-A53.
Fixes: f01982e ("sunxi: add testing kernel 6.1")
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
Link: https://github.com/openwrt/openwrt/pull/20140
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is Allwinner's ARM926EJ-S core, which is one of its early
products, reappearing in recent compact designs. The SoC includes
32/64Mb memory in the same physical package, and has display and USB
interfaces, allowing for very small footprint boards.
The target consists of basic 6.12 support, with u-boot. Instead of creating
a separate suniv target, as both the kernel and u-boot supports enough of
this SoC by now with minimal patching, add it into sunxi as a subtarget.
Link: https://github.com/openwrt/openwrt/pull/15022
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Certain boards have an at24(-compatible) EEPROM for storing various
parameters like MAC addresses. Enable support for this hardware across
the whole target.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Modernize the target slightly to use kernel+dtb FIT images in all
subtargets. LZMA compression will be used for the cortexa53 devices,
and we'll stay conservative and use gzip for the cortexa7/a8 devices
due to performance differences.
Tested-on:
- Linksprite pcDuino v2 (cortexa8 / A10)
- Olinuxino Micro (cortexa7 / A20)
- Banana Pi M2 Berry (cortexa7 / V40)
- Banana Pi P2 Zero (cortexa7 / H2+)
- Xunlong Orange Pi 2 (cortexa7/ H3)
- OrangePi PC Zero 2 (cortexa53 / H616)
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
RTC has been disabled so far in the cortexa53 subtarget so far, enable
it. It's also required for the crypto trng/prng drivers on these SoC
variants (to gather IOSC noise).
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
The CONFIG_NET_SWITCHDEV option is needed by CONFIG_DSA and some other
options. It is boolean, we have to compile it into the kernel it self.
Activate it for all targets in the generic configuration, it is already
activated for most of them. This allows to install DSA drivers as a
module.
On the ramips/mt7620 target the kernel would grown by 4.5kB.
For some small targets which do not support a DSA switch by default the
option is deactivated.
Link: https://github.com/openwrt/openwrt/pull/17668
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specifications:
- SoC: Allwinner A31 @ 1GHz
- DRAM: 1/2Gb DDR3
- SD-card slot
- NAND: 8/16Gb MLC
- Ethernet: 1x 10/100/1000Mbps (RTL8211E)
- Wireless: Ampak AP6210 (BCM43362)
- 2x USB2.0
- 1x mPCIe slot for 4G cards
- 1x SIM slot
- HDMI/VGA via simplefb
- RTC with battery
- Power via DC12V / 3A
Installation:
Use the standard sunxi installation to an SD-card. NAND is
not supported.
This is to re-add proper support for an older device.
Link: https://openwrt.org/toh/merrii/hummingbird
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Sander van Deijck
John Audia
Joseph Chen
Edoardo Pinci
Daniel Golle
Zoltan HERPAI
Shiji Yang
Hauke Mehrtens
Mario Andrés Pérez
Chukun Pan
Álvaro Fernández Rojas
Kyle Hendry