Enable MACsec (Media Access Control Security) support in the Mellanox
mlx5 driver by setting CONFIG_MLX5_MACSEC=y.
Enabling this configuration allows users to utilize hardware MACsec
offload capabilities on supported Mellanox ConnectX network adapters.
This provides point-to-point Layer 2 encryption at line rate while
significantly reducing CPU overhead.
The kmod-macsec dependency is intentionally omitted to make this an
opt-in feature. The offload support only builds if kmod-macsec is
also selected, preventing driver bloat for standard users.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/25400
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add the two external Aeonsemi AS21xxx PHYs used by the LAN and WAN
10GBASE-T ports of the BPI-R4 Pro 8x. Configure their firmware, reset
timing and LEDs, and connect them to the MxL switch and GMAC1.
Replace the fixed SFP GPIO hog configuration with LAN and WAN overlays
selecting either the copper PHY or the corresponding SFP cage. Build all
four overlays, include them in the device image and select the SFP
overlays by default through U-Boot `bootconf_extra`.
Make the AS21xxx firmware package pull in the PHY driver on Linux 6.18,
instead of making the driver depend on the firmware. Update existing
Airoha device package lists accordingly so they continue to install both
components through the firmware package.
Breaking change for users using the router with SFP hogs from PR #21083.
After flashing the new image, configure `bootconf_extra` to select
between SFP or PHY overlays:
fw_setenv bootconf_extra \
mt7988a-bananapi-bpi-r4-pro-8x-lan-phy#mt7988a-bananapi-bpi-r4-pro-8x-wan-phy
If bootconf_extra had additional overlays (CN13 or CN14) keep them appended
Signed-off-by: Pietro Ameruoso <p.ameruoso@live.it>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This improves on openwrt/openwrt@aeb9028aab by adding support for
other Dell EMC Edge620/640/680 devices and mapping
the interfaces to match the markings on the device.
This modifies the netdevices.mk file to set the boot flag for
ixgbe driver to load it in early stage of the boot process to
allow for proper mapping of the network interface PCI paths
inside the 02_network script. This will also allow other devices
using the ixgbe driver to do proper mapping in 02_network script.
The 02_network script is then modified to support all
dell-emc-620/640/680 devices. It now maps the network
interfaces via PCI paths to match the markings on the device.
The interface marked GE6 is still used for WAN with
interfaces GE1-GE5 used for LAN.
The SFP1 and SFP2 interfaces are left to be assigned by
the user.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/23110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Motorcomm YT6801 is a PCIe ethernet controller based on DWMAC4 IP. It
integrates an GbE phy, supporting WOL, VLAN tagging and various types
of offloading. It ships an on-chip eFuse for storing various vendor
configuration, including MAC address.
The PM and plat_data functions were slightly modified to build with
current kernel.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace conditional "LINUX_6_12:mod" / "!LINUX_6_12:mod" AUTOLOAD entries
with version-filtered module names using @lt6.18 / @ge6.18. This makes
version_filter emit plain module names into /etc/modules.d(e.g. "crc32c_generic"),
allowing kmodloader to find and load the correct module for the running kernel.
Fixes crc32c (and related crypto modules) not being autoloaded on 6.12 kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing dependency kmod-ptp to fix the build error. We also
add symbol CONFIG_PTP_1588_CLOCK_OPTIONAL explicitly for kmod-ptp
because it is selected by CONFIG_PTP_1588_CLOCK. Fix:
Package kmod-iavf is missing dependencies for the following libraries:
ptp.ko
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Backport upstream driver and apply pending downstream patches to
support using the MaxLinear MxL86252 and MxL86282 switches.
The driver supports a native proprietary 8-byte DSA special tag format
(mxl862xx) as well as using an 802.1Q-based DSA tag (mxl862xx-8021q).
All basic bridge, VLAN and LAG operations are supported. A single port
can be used as mirror port. Hardware counters are made available as
ethtool stats or directly serve as interface counters (bytes,
packets).
The switch runs a complex ZephyrOS-based firmware on an integrated
ARC microcontroller, the driver uses the firmware management API over
MDIO to interact with the switch hardware.
Note that the firmware needs to be rather recent (WSP 1.0.78 or later)
to work well with this driver. It can be updated at runtime using devlink.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This adds kernel packages for the Microchip KSZ9477 switch family.
The core package has a target specific dependency as the ksz9477
driver enables DCB which grows the kernel size and can negatively
impact other targets.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Link: https://github.com/openwrt/openwrt/pull/22257
Signed-off-by: Robert Marko <robimarko@gmail.com>
This reverts commit c053b22573.
KSZ DSA driver is the only thing in the kernel selecting DCB support
instead of depending on it if required.
So, it will enable DCB support without asking and we do not want the
kernel size increase, as well as current Layerscape ARMv8 build failure.
So, revert this until its fixed upstream or worked around.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Switchdev driver used by microchipsw supports DCB and has not storage
constraints, so enable kernel and driver DCB support by default.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The Motorcomm YT8821 2.5G PHY is being used in some devices as an
alternative to devices like the RTL8221B. Package it as a kmod
so it can be used as a device package rather than requiring changes
to the target kernel config.
Signed-off-by: Andrew MacIntyre <andymac@pcug.org.au>
Link: https://github.com/openwrt/openwrt/pull/21399
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Previously, devices would have to select `CONFIG_RTL8261N_PHY=Y` in the
whole target's kernel config. Now that this driver is becoming usable
for devices other than Realtek switches, allow packaging this driver
separately.
Signed-off-by: Kenneth Kasilag <kenneth@kasilag.me>
Link: https://github.com/openwrt/openwrt/pull/20429
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Currently, the interfaces of the Mellanox Spectrum Switch QSFP ports
are all labeled eth*. Their order doesn't match the faceplate and is
different for each model.
They could be named during boot, but this isn't sufficient because they
support port splitting. After such ports are split, their port naming
begins again with eth*, and the same is true after they are unsplit again.
A hotplug script is used here that reads from the sysfs file
phys_port_name, which contains p1, p2, p3, ... for unsplit ports
and p1s0, p1s1, p1s2 for split ports.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Set the pre-init boot flag for the e1000e network device
driver so that it is loaded during the early pre-init
stage of the boot process instead of later.
Then, it is possible to rename its network ports via the
ucidef_set_network_device_path function from the
02_network script while booting.
Signed-off-by: Til Kaiser <mail@tk154.de>
Link: https://github.com/openwrt/openwrt/pull/17251
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix a typo on defining the PHY package kmod description that reference
phy-aeonsemi-as21x1x package instead of phy-aeonsemi-as21xxx.
Fixes: 08a616b216 ("generic: backport support for Aeonsemi AS21xxx PHY")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Converts the KS8995 "phy" driver to a proper DSA switch.
Currently the upstream only supports the "none" tag
but this is a good improvement already.
Make the old module depend on kernel 6.6 and the new
one depend on !6.6.
The Realtek RTL8261n patch needs to be refreshed
because of textual dependencies.
Realtek RTL838x DSA and phy patches also have textual
dependencies and need to be refreshed.
The Mediatek in-flight DSA patch and related patches
also need to be rebased and refreshed.
Link: https://github.com/openwrt/openwrt/pull/19970
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Backport support for Aeonsemi AS121xxx PHY. The PHY require dedicated
firmware to be loaded to correctly work and support a big family of
Aeonsemi PHY that provide from 1G to 10G speed.
Automatically refresh all affected patch and file (rtl PHY).
Link: https://github.com/openwrt/openwrt/pull/19816
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
kmod-sfc should add support for Solarflare SFC9000 series based cards.
However after kernel 5.19, support for the 'Siena' subclass of
SFN5000/6000 devices has been separated out since they went EOL as they
are no longer being actively developed. As kmod-sfc no longer provides
driver support for these cards and hasn't since kernel 5.2, a new kernel
module is needed to support these 10Gb Ethernet cards. More info here:
https://cateee.net/lkddb/web-lkddb/SFC_SIENA.html and here:
https://www.phoronix.com/news/Solarflare-SFC-Siena-Linux-5.19
The module can be compiled in separately and works if kernel is custom
compiled;
OpenWRT has made these changes already with the SFC 'falcon' subclass of
drivers already. See 3c5d70a and e5ba6e9
This is building on excellent work by @ynezz and @nasbdh9
Signed-off-by: Steve Wavler <trenchcoatjedi@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19647
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The CONFIG_BCMGENET kernel config option will select this driver. Add
the driver to the kernel config menu and make kmod-bcmgenet depend on
it.
Link: https://github.com/openwrt/openwrt/pull/19480
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In the development history of Intel's drivers, the i40evf driver was later
renamed the iavf driver. For example, some documents mention that
Intel® Network Connections Software Version 24.0 renamed the i40evf
and ixlv drivers to iavf. In subsequent versions, the i40evf driver was
gradually removed, and its functions were taken over by the iavf driver.
In the Linux system, relevant configuration instructions also exist. For
instance, the User Guide for X722 Onboard Network Card states that the
i40evf driver module should be disabled, and the iavf driver should be
installed and used.
blamed commit: https://github.com/openwrt/openwrt/commit/5d81b28a829ac20fb60991e71ee7a7c53d14fd58
Signed-off-by: xiao bo <peterwillcn@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/19197
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport accepted BCM5325 patches from net-next.
These patches will be merged in the v6.17 kernel window.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
The ENC28J60 is a 10 Mbps half-duplex Ethernet controller interfaced via SPI.
It achieves real-world bandwidth up to 5Mbit/s on devices like the RPi Zero due
to SPI limits.
Commonly used with Raspberry Pi Zero boards for wired network connectivity.
Signed-off-by: Albrecht Lohofener <albrechtloh@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/19048
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
This reverts commit 5687f448a4.
This unfortunately is currently breaking all targets during building
as in 6.6 kernel there is
no CONFIG_NET_DSA_TAG_VSC73XX_8021Q, it was added in 6.11 AFAIK.
So they will all fail due to $(LINUX_DIR)/net/dsa/tag_vsc73xx_8021q.ko missing.
So revert until kmod is fixed.
Signed-off-by: Robert Marko <robimarko@gmail.com>
Til Kaiser
Frank Wunderlich
Shiji Yang
Andris PE
Daniel Golle
Raylynn Knight
Philip Prindeville
Tianling Shen
Mieczyslaw Nalewaj
Tan Zien
Tim Harvey
Robert Marko
Robert Marko
Andrew MacIntyre
Yanase Yuki
George Sapkin
Kenneth Kasilag
Christian Marangi
Linus Walleij
Steve Wavler
Hauke Mehrtens
xiao bo
Mantas Pucka
Alexandru Gagniuc
Álvaro Fernández Rojas
Mathew McBride
Albrecht Lohofener
Coia Prant