The LED init script sets the DSL LED to its configured trigger. If the
modem is in the middle of the handshake or the training at that point,
the LED stops blinking until the line changes its state again. That is
why the DSL control scripts start after the LED init script, at the
very end of the boot process.
Remember the last state of the line in dsl_notify.sh, which gets every
event of the modem, and show it again right after the LED init script,
so that the modem can be started earlier. The state is written before
the LED is updated, so an event during the replay is shown afterwards.
Assisted-by: Claude:claude-fable-5-1
Assisted-by: Claude:claude-opus-5-5
Link: https://github.com/openwrt/openwrt/pull/25599
Signed-off-by: Nick Hainke <vincent@systemli.org>
Add a vendor profile for Fibocom modems so that proto ncm can drive them.
Without it ncm.sh reports UNSUPPORTED_MODEM, as the manufacturer string
returned by AT+CGMI has no matching key in ncm.json.
The FG621-EA is used in the ASUS 4G-AX56 and the TP-Link TL-MR500 v1. The
profile keys off the manufacturer string rather than any particular board,
so it applies to Fibocom NCM modems generally.
ncm.json is installed by comgt-ncm, so bump PKG_RELEASE to make sure
existing installations pick up the new vendor profile on upgrade.
This change originates from PR #19793 by kddred, open in draft since
August 2025 without review. The original commit is authored and signed
off with a GitHub noreply address, which the commit formality check
rejects, so it could not be carried unmodified, and kddred has not been
active since August 2025. Authorship is reassigned for that reason alone;
the work is theirs. Happy to restore the original authorship if a usable
address becomes available.
Tested on an ASUS 4G-AX56 (HW rev A1) on both main and openwrt-25.12.
Link: https://github.com/openwrt/openwrt/pull/19793
Signed-off-by: Fredrik Hallin <fredappsdev@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/24974
Signed-off-by: Jonas Jelonek <jonas@jonasjelonek.de>
The configure script of xdp-tools sets ARCH_INCLUDES only from the
multiarch directory of a native compiler. For a cross compiler it stays
empty, and clang takes <linux/types.h> for the BPF programs from
/usr/include of the host. On hosts that have <asm/types.h> only in the
multiarch directory, such as Debian without gcc-multilib, the build
fails:
/usr/include/linux/types.h:5:10: fatal error: 'asm/types.h' file not found
Add the include directories of the toolchain with -idirafter. They are
searched after the headers of xdp-tools and of the system, as the
multiarch directory of a native build, so they do not replace the Linux
headers that xdp-tools ships. The target compiler already has them as
system directories.
The configure script also tests for bpftool with the bash redirection &>.
/bin/sh may be dash, which runs the command in the background instead, so
configure drops a working bpftool and takes the output of whereis. Add a
second patch that uses >/dev/null 2>&1, which every shell supports.
Signed-off-by: John Crispin <john@phrozen.org>
The ncm.json entry is picked from AT+CGMI alone, so every modem from a
vendor has to share one dialect. That does not hold for Quectel: the
EG060W answers "operation not supported" to AT+QICSGP on context 1, the
attached default bearer, while EC25/EG25 need AT+QICSGP because it is
what carries username, password and auth.
Read AT+CGMM as well and prefer a "<manufacturer>-<model>" entry, falling
back to the plain manufacturer entry, so existing profiles behave exactly
as before. The region suffix is dropped, EG060W-EAAA becomes eg060w.
json_is_a() is used rather than a bare json_select() so a modem without a
model specific entry does not log a warning.
Add quectel-eg060w, which configures the context with AT+CGDCONT.
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Tested-by: Fredrik Hallin <fredappsdev@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/24689
Signed-off-by: Jonas Jelonek <jonas@jonasjelonek.de>
Some modems raise carrier as soon as the data call is enabled and drop it
again briefly while the connection is finalised. On a Quectel EG060W the drop
is about a second long and lands about two seconds after AT+QNETDEVCTL, with
no configuration command involved at all. Not every modem does it: a Fibocom
FG621-EA sampled at ~90 Hz over three cycles never dropped carrier.
netifd turns that transient into a permanent failure: the DHCP sub-interface
is dynamic and created only once during setup, and a dynamic interface is
removed on carrier loss (IFC_REMOVE in interface_check_state()), so nothing
ever recreates it. udhcpc is usually still sending discovers when the drop
kills it, and the interface is left with no address and no route. If the drop
lands after a lease was granted the lease is stale instead, and a renew does
not recover that either because it unicasts to a server that no longer exists.
Wait for the carrier to stay up for a few seconds before handing the interface
to netifd, so the drop falls outside the window netifd is watching.
directip.sh already waits for carrier for the same class of reason ("wait for
carrier to avoid firmware stability bugs") and qmi.sh sleeps unconditionally
while waiting for registration; unlike those this is tunable, and linksettle 0
keeps the previous behaviour.
The wait gives up after three times linksettle, floored at 30s so it always
outlasts the settle window, and continues anyway. Profiles that only reach
data state at finalize, further down, have nothing to wait for here and skip
it; mtk1 is marked with linkatfinalize for that.
Measured on an EG060W (Cudy LT700 Outdoor), three runs each: with linksettle 0
udhcpc never obtains a lease, the dynamic interface is torn down and the link
stays dead; with the 3s default the lease, route and traffic come up every
time, and netifd logs no carrier loss at all.
On a modem without the drop the wait only adds linksettle seconds to the
bring-up (14s vs 17s on the FG621-EA). It stays on by default anyway: a missed
drop leaves the link permanently dead rather than slow, and it is not known in
advance which modems do it. linksettle 0 turns it off where it is not needed.
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Tested-by: Fredrik Hallin <fredappsdev@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/24689
Signed-off-by: Jonas Jelonek <jonas@jonasjelonek.de>
proto_ncm_setup() parses the AT+CGMI reply with RS='\r?\n',
proto_ncm_teardown() does not. The manufacturer ends up as "quectel\r",
json_select fails with "Unsupported modem" and teardown returns before
sending the disconnect command, leaving the data call up on the modem.
A blank CRLF line hits the same path: \r is not whitespace for the
default FS, so a record holding only \r still has NF == 1 and is taken
as the manufacturer.
This affects every vendor whose reply is a single token. "zte" comes out
the same either way, its reply is "ZTE INCORPORATED" so the CR sits past
$1.
Note that teardown now reaches the disconnect command on modems where it
silently never did, so those commands actually get sent on ifdown.
Signed-off-by: Carlo Szelinsky <github@szelinsky.de>
Link: https://github.com/openwrt/openwrt/pull/24689
Signed-off-by: Jonas Jelonek <jonas@jonasjelonek.de>
The ucode split helper keeps empty fields when a string has leading or
trailing whitespace.
Trim string values before splitting so addresses and allowed_ips retain
the old shell handler behavior and do not produce empty entries.
Signed-off-by: Dharmik Parmar <dharmikparmar2004@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/24121
Signed-off-by: Robert Marko <robimarko@gmail.com>
This is required to add available dns servers in ifstatus output,
required by downstream tools to receive information of the configured
DNS server on the wwan interface.
This has no effect on the dns server selection, as peerdns has the
desired effect within netifd.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
This is required to add available dns servers in ifstatus output,
required by downstream tools to receive information of the configured
DNS server on the wwan interface.
This has no effect on the dns server selection, as peerdns has the
desired effect within netifd.
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
A patch was added without proper header and not obvious that it's a
backport. Replace that patch with a backport of the upstream commit.
Patch 001-build-simplify-the-instantiation-of-nftversion-h.patch
rebased, all others refreshed.
Fixes: 255f4c8e60 ("packages: nftables: fix build on host with busybox ash")
Link: https://github.com/openwrt/openwrt/pull/23910
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Bump the PKG_RELEASE as it was missed when adding a patch.
Fixes: 255f4c8e60 ("packages: nftables: fix build on host with busybox ash")
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Version 7.0 - Apr 28, 2026
* Feature: support MSE display (--show-mse)
* Feature: add 2 new link_ext_state names
* Fix: fix index calculation in ixgbe register dump (-d)
* Fix: cmis wavelength tolerance output (-m)
* Fix: duplicate sfpid Active Cu compliance output (-m)
Signed-off-by: Paul Donald <newtwen+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23574
Signed-off-by: Robert Marko <robimarko@gmail.com>
The current 150s watchdog timeout is too aggressive, leading to
premature hostname re-resolution on alive connections.
Even with a 25s keepalive, handshakes may not occur within the 150s window.
Increasing the timeout to 180s aligns the watchdog with WireGuard's
REJECT_AFTER_TIME constant, ensuring we only re-resolve when the connection
is truly considered dead.
Signed-off-by: Roberto Almeida Silva <robertoalmeidasilva1981@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23248
Signed-off-by: Robert Marko <robimarko@gmail.com>
Backport upstream iw commit d90618809e06 ("iw: scan: print RSN
Element Override IEs") as 001-*.patch so `iw scan` decodes the
RSNOE (vendor WFA type 41) and RSNO2E (type 42) elements that
hostapd emits for WPA3 Compatibility / RSN Overriding APs.
Also refresh the hunk offsets in 200-reduce_size.patch.
Link: https://github.com/openwrt/openwrt/pull/23009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Two of the IW_FULL guards in 200-reduce_size.patch were inverted
or incomplete:
* the "unknown event" handler unconditionally replaced the
verbose print with the short form, so IW_FULL builds lost
the command name decoding;
* the early return before the vendor IE parser used
#ifdef IW_FULL, which suppressed parsing in the full build
instead of the size-reduced one.
Wrap both with the correct #ifndef IW_FULL / #else so the full
and reduced builds produce the intended output.
Link: https://github.com/openwrt/openwrt/pull/23009
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add patches to fix build failures on musl-based toolchains:
0002-xdpsock-fix-struct-ethhdr-redefinition-on-musl.patch:
xdpsock.c included <net/ethernet.h> and <netinet/ether.h> alongside
<linux/if_ether.h>, triggering a struct ethhdr redefinition on musl.
Replace BSD-style ether_header/ether_addr with struct ethhdr and drop
the conflicting includes.
0003-build-use-gnu2x-to-avoid-stdbool.h-dependency.patch:
Switch CFLAGS and BPF_CFLAGS from -std=gnu11 to -std=gnu2x. In C23,
bool is a native keyword, fixing "stdbool.h: No such file or directory"
errors with a clang lacking its resource directory (e.g. llvm-bpf built
with LLVM_INSTALL_TOOLCHAIN_ONLY=ON on musl targets).
Link: https://github.com/openwrt/openwrt/pull/22983
Signed-off-by: Nick Hainke <vincent@systemli.org>
The rss-input-xfrm workaround for Linux 6.6 is no longer needed with
current kernel versions. Remove the patch and the associated
--enable-rss-input-xfrm configure flag.
Link: https://github.com/openwrt/openwrt/pull/22841
Signed-off-by: Nick Hainke <vincent@systemli.org>
Version 6.19 - Feb 14, 2026
* Feature: support HW timestamp configuration (--set-hwtimestamp-cfg)
* Feature: display HW timestamp source (-T)
* Feature: support PLCA notifications (--get/set-plca-cfg)
* Feature: add PSE priority management support (--show/set-pse)
* Feature: support PSE notifications (--show/set-pse)
* Feature: support configuring RSS on IPv6 Flow Label (-n/-N)
* Feature: support FEC bit error histograms (--show-fec)
* Feature: register dump decoding for TI K3 CPSW and its ALE table (-d)
* Fix: fix missing headers in text output
* Fix: fix print_string when the value is NULL (-Werror=format-security)
* Fix: fix JSON output of SFP diagnostics
* Fix: fix duplicated JSON keys in module info
* Misc: clarify that symmetric RSS may be on by default (-x/-X)
* Misc: add AppStream metainfo file to %files section
Link: https://github.com/openwrt/openwrt/pull/22780
Signed-off-by: Nick Hainke <vincent@systemli.org>
The conditional runtime dependency on the ip package was originally
intended to only pull in the ip package when busybox ip is not
configured. However, in APK-based builds the BUSYBOX_CONFIG_*
variables may not be resolvable at package metadata generation
time, causing the ip dependency to be unconditionally baked into
the .apk package. This forces users to install ip-tiny or ip-full
even though busybox already provides the ip command.
Revert to the previous +@BUSYBOX_CONFIG_IP / +@BUSYBOX_CONFIG_FEATURE_IP_LINK
kconfig-level dependencies. These ensure busybox ip support is
enabled at config time without creating a runtime package dependency.
Both options default to y, and wireguard.uc only uses basic
ip link commands that busybox fully supports.
Fixes: openwrt#22637
Signed-off-by: Anand Kumar <anandvtu16158@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22652
Signed-off-by: Robert Marko <robimarko@gmail.com>
% git shortlog v1.0.20250521..v1.0.20260223
Doug Freed (1):
wg-quick@.service: add deps on wg-quick.target
Jason A. Donenfeld (8):
wg-quick: linux: use smallest mtu, not largest
syncconf: account for psks removed from config file
wg-quick: linux: deal with resolvconf migration more gracefully
wg-quick: use addconf instead of setconf
wg-quick: linux: do not unnecessarily set sysctl
config: preserve const correctness
syncconf: account for persistent keepalive removed from config file
version: bump
Robyn Kosching (1):
wg-quick: pass on # comments to {Pre,Post}{Up,Down}
Build system: x86/64
Build-tested: x86/64-glibc
Run-tested: x86/64-glibc
Signed-off-by: John Audia <therealgraysky@proton.me>
Link: https://github.com/openwrt/openwrt/pull/22190
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXqmiX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'qmi'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Introduce the devpath option to find the control channel device from a
hardware path for a USB or a WWAN device.
This option is useful when there are multiple modems connected to the
system. The name of the control channel device of a modem can change
depending on which modem initialises first or if it was recently plugged
in. The devpath option allows specifying the hardware path of the modem
where the control channel device will be found using that.
For the USB device hardware path, it is allowed to specify the USB port
number the modem is directly connected to.
If the device and devpath options are both set, devpath takes precedence
over device.
The USB device hardware path of a control channel device can be found by:
readlink -f /sys/class/usbmisc/cdc-wdmX/device
The WWAN device hardware path of a control channel device can be found by:
readlink -f /sys/class/wwan/wwanXmbimX/device
An example uci configuration would be:
config interface 'wwan_usb1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/1e1c0000.xhci/usb1/1-1'
option apn 'internet'
option pdptype 'ipv4v6'
Or:
config interface 'wwan_pcie1'
option proto 'mbim'
option auth 'none'
option devpath '/sys/devices/platform/soc/11280000.pcie/pci0003:00/0003:00:00.0/0003:01:00.0'
option apn 'internet'
option pdptype 'ipv4v6'
Signed-off-by: Chester A. Unal <chester.a.unal@arinc9.com>
Due to a missing include, the constant UINT_MAX is undefined. This
fixes issues when building v25.12.0-rc5. Including a newer version of
iproute2 would include the patch, but causes other building issues.
Signed-off-by: Jonas Lochmann <openwrt@jonaslochmann.de>
Link: https://github.com/openwrt/openwrt/pull/22128
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Use substr() instead of array index syntax to access the first
character of the endpoint host string, as ucode does not support
array-style indexing on strings.
Fixes: https://github.com/openwrt/openwrt/issues/22116
Fixes: 8f977b4a40 ("wireguard-tools: fix handling of multi-value config options")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Config options like addresses and ip6prefix can be passed as either a
space-separated string or an array. Add a to_array() helper and use it
consistently for all multi-value options (addresses, ip6prefix,
allowed_ips).
Fixes: https://github.com/openwrt/openwrt/issues/22102
Fixes: 41bc454602 ("wireguard-tools: rewrite proto handler in ucode")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Add a patch that avoids including <stddef.h> in BPF headers, fixing
build failures on OpenWrt toolchains where the header is unavailable:
In file included from xdpfilt_dny_udp.c:10:
In file included from ./xdpfilt_prog.h:24:
../lib/../headers/xdp/parsing_helpers.h:18:10: fatal error: 'stddef.h' file not found
18 | #include <stddef.h>
| ^~~~~~~~~~
1 error generated.
make[5]: *** [../lib/common.mk:111: xdpfilt_dny_udp.o] Error 1
make[4]: *** [Makefile:40: xdp-filter] Error 2
Link: https://github.com/openwrt/openwrt/pull/21972
Signed-off-by: Nick Hainke <vincent@systemli.org>
Nick Hainke
Paul Spooren
Ivan Pavlov
Fredrik Hallin
John Crispin
Carlo Szelinsky
Dharmik Parmar
Florian Maurer
Aleksander Jan Bajkowski
Erik Conijn
Pawel Dembicki
Jonas Jelonek
Shine
Paul Donald
Hauke Mehrtens
David Bauer
Roberto Almeida Silva
Philip Prindeville
Anand Kumar
Eric Fahlgren
John Audia
Chester A. Unal
Jonas Lochmann
Felix Fietkau
Rui Salvaterra