Add pending patches which add a PSE driver for the PSE setup found on
most of Realtek-based switches. An MCU with a Realtek-defined firmware
and protocol fronts one or more PSE chips (from Realtek or Broadcom) as
a management controller.
The driver provides both I2C/SMBus and UART communication, which varies
among our supported switches. There is no need for complicated userspace
handling anymore, the PSE setup is defined in the device tree and
interfaced in userspace via ethtool, netlink and netifd support.
Those patches have progressed far enough upstream, the bindings are
reviewed. Thus, we can keep this intermediate version downstream to open
it up earlier for usage. Only little changes are expected til the final
version lands.
Link: https://github.com/openwrt/openwrt/pull/23222
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
The bcm27xx/bcm2708 all-kmods CI build fails when modpost reaches the
DesignWare I2C core module:
ERROR: modpost: "__aeabi_uldivmod"
[drivers/i2c/busses/i2c-designware-core.ko] undefined!
This is triggered by CONFIG_ALL_KMODS=y. The old 32-bit Raspberry Pi
subtargets do not normally select this driver for runtime use, but all-kmods
forces the kmod package to be built anyway. On 32-bit ARM, raw 64-bit
division in a module can cause GCC to emit the ARM EABI helper
__aeabi_uldivmod, which is not available as a kernel module symbol.
The failing reference comes from i2c-designware-master.c, where clock_calc()
uses raw u64 division for SCL timing calculations (introduced with commit
3805d13c3ead21494f7d00aa44f10e3656363d4c in rpi-6.18.y / "i2c: designware:
Support non-standard bus speeds"). That is a kernel-side portability issue,
but these old bcm27xx subtargets do not use DesignWare I2C hardware. They
use the Broadcom I2C controller instead.
The failure is emitted for i2c-designware-core.ko, so guard the hidden core
package itself rather than only guarding the platform or PCI frontend package.
This prevents CONFIG_ALL_KMODS from selecting the failing core module directly
on the affected 32-bit bcm27xx subtargets.
DesignWare I2C is relevant for newer Raspberry Pi 5 / RP1 based systems, so
keep it available for bcm2712.
A similar issue was reported by NixOS for Raspberry Pi ARM builds, where
i2c-designware-core.ko failed with the same unresolved __aeabi_uldivmod symbol.
Their workaround was to disable the DesignWare I2C symbols for older Raspberry
Pi targets that do not need them.
Link: https://github.com/NixOS/nixpkgs/issues/464515
Until the underlying ARM32 kernel-side issue is fixed, avoid building
the DesignWare core package on bcm2708, bcm2709 and bcm2710.
Signed-off-by: Joshua Covington <joshuacov@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23703
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
These path names are unlikely to change. There is no need for variables.
Tested on Turris Omnia, but not all of these drivers were tested. Variables
were replaced automatically (search-and-replace in text editor). There
shouldn't be any problems.
Signed-off-by: Marius Dinu <m95d+git@psihoexpert.ro>
Create a package for ov5645 kernel module, required to support camera on
PICO-PI-IMX7D board.
Currently limit the visibility to imx_cortexa7 subtarget, but this can
be enabled on other platforms if needed.
Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/17606
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Split kmod-nf-nathelper-extra into separate helper packages
and keep the original package as a compatibility meta-package.
This allows selecting only the required protocol helpers
instead of installing all helper modules and dependencies.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23690
Signed-off-by: Robert Marko <robimarko@gmail.com>
LED trigger for network interfaces.
- Aggregated per-family (lan/wan/wlan).
- Family and flags are taken from device tree properties:
- "family" : simple family string "lan" | "wan" | "wlan"
- "mode" : any combination of "link", "tx", "rx" flags
Priority/combination:
* If "mode" present: flags come from "mode" and take precedence.
Family is taken from "family" if present, otherwise from the LED name.
* If only "family" present: use its family and default flags = link+tx+rx.
* If neither present: fall back to LED device name parsing.
- Suffix "-online" is valid ONLY in the LED name (label),
e.g. "green:wlan-online". It indicates the online variant but is applied
only when DT "mode" is absent.
Behaviour:
- wlan (normal): blink/solid driven by throughput table
- lan/wan (normal): one-shot blink on TX/RX packet change
- *-online variants: steady ON while any interface of the family has carrier
Interfaces are auto-tracked by name match (lan0, wan1, wlan2, phy0, wl1,
ath0, ra0...). Up to MAX_IFACES (16) interfaces per family
This trigger is intended for board/device authors and drivers to provide simple
network-activity LED behaviour without per-interface wiring in userspace.
Refresh bcm27xx patches in the same commit to account for line shifts in
drivers/leds/trigger/Kconfig and Makefile, ensuring clean applies for
bisectability.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19903
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Micro Crystal RV3028 I2C real-time clock chip.
Tested on a Kontron OSM-S/BL i.MX8MP eval board.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Since upstream commit 60e3f1e9b7a5 ("lib/crypto: arm64/sha512:
Migrate optimized SHA-512 code to library"), the kernel module is no
longer available, and its fucntionality os provided by the kernel
core. Thus do not try to package this for linux 6.18 and later.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21506
Signed-off-by: Robert Marko <robimarko@gmail.com>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The AddDepends/pse-pd helper appended kmod-pse-pd to DEPENDS without the
'+' prefix, making it a hard dependency rather than an auto-selecting one.
This breaks pulling any PSE controller driver (kmod-pse-pd692x0,
kmod-pse-si3474, kmod-pse-tps23881, kmod-pse-regulator, ...) in via a
device's DEVICE_PACKAGES: the kmod itself is auto-selected, but the
unsatisfied hard dep on kmod-pse-pd silently drops it from .config.
Prefix the kmod-pse-pd entry with '+' so it auto-selects, matching how
the other deps in the same file (kmod-i2c-core, etc.) are expressed. The
helper is the right place to fix this; every PSE controller driver routes
through it.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23449
Signed-off-by: Robert Marko <robimarko@gmail.com>
OSLEC has been dropped upstream since Linux 6.16.
Reflect that by no longer providing the kernel module package
`kmod-echo` which essentially became an empty stub.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This improves on openwrt/openwrt@aeb9028aab by adding support for
other Dell EMC Edge620/640/680 devices and mapping
the interfaces to match the markings on the device.
This modifies the netdevices.mk file to set the boot flag for
ixgbe driver to load it in early stage of the boot process to
allow for proper mapping of the network interface PCI paths
inside the 02_network script. This will also allow other devices
using the ixgbe driver to do proper mapping in 02_network script.
The 02_network script is then modified to support all
dell-emc-620/640/680 devices. It now maps the network
interfaces via PCI paths to match the markings on the device.
The interface marked GE6 is still used for WAN with
interfaces GE1-GE5 used for LAN.
The SFP1 and SFP2 interfaces are left to be assigned by
the user.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/23110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Select `CONFIG_ROCKCHIP_SARADC=y` to enable Rockchip SAR ADC
Add ADC Ladder Buttons driver as a kernel module as well as `kmod-button-hotplug` to the list of
default packages for Rockchip targets that have buttons connected to ADC, not including some
devices (e.g. NanoPi R76S) that have ADC buttons which are not in the device tree.
This is needed to use buttons on Rockchip devices that are connected to ADC and not GPIO
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-sound-midi2 expects sound/core/snd-ump.ko, but
CONFIG_SND_UMP=y builds it in-kernel rather than as
a module. Replace the forced built-in setting with
plain CONFIG_SND_UMP so the module can be packaged
correctly.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23265
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fix dependency for kmod-drm-client-lib module:
error: recursive dependency detected!
symbol LINUX_6_18 is selected by PACKAGE_kmod-drm-client-lib
symbol PACKAGE_kmod-drm-client-lib is selected by LINUX_6_18
Fixes: e75ba35ed8 ("modules: video: introduce DRM client setup module")
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux commit c9e5ac0 ("lib/crypto: mips/md5: Migrate optimized code into
library") removed the MIPS-Octeon-specific MD5 implementation
(octeon-md5.ko) and replaced it with an optimized library implementation
in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_OCTEON and the module
arch/mips/crypto/octeon-md5.ko no longer exist in kernels >= 6.18.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23031
Signed-off-by: Nick Hainke <vincent@systemli.org>
6.14 has introduced a DRM client setup library. Add kmod-drm-client-lib
to support it, and add it as a dependency to DRM modules which depend on it.
Link: https://github.com/openwrt/openwrt/pull/22975
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Motorcomm YT6801 is a PCIe ethernet controller based on DWMAC4 IP. It
integrates an GbE phy, supporting WOL, VLAN tagging and various types
of offloading. It ships an on-chip eFuse for storing various vendor
configuration, including MAC address.
The PM and plat_data functions were slightly modified to build with
current kernel.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux commit 09371e1349c9 ("lib/crypto: powerpc/md5: Migrate optimized code into library")
removed the PowerPC-specific MD5 implementation (md5-ppc.ko) and
replaced it with an optimized library implementation in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_PPC and the module
arch/powerpc/crypto/md5-ppc.ko no longer exist in kernels >= 6.18.
Link: https://github.com/openwrt/openwrt/pull/22732
Signed-off-by: Nick Hainke <vincent@systemli.org>
Replace conditional "LINUX_6_12:mod" / "!LINUX_6_12:mod" AUTOLOAD entries
with version-filtered module names using @lt6.18 / @ge6.18. This makes
version_filter emit plain module names into /etc/modules.d(e.g. "crc32c_generic"),
allowing kmodloader to find and load the correct module for the running kernel.
Fixes crc32c (and related crypto modules) not being autoloaded on 6.12 kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add missing dependency kmod-ptp to fix the build error. We also
add symbol CONFIG_PTP_1588_CLOCK_OPTIONAL explicitly for kmod-ptp
because it is selected by CONFIG_PTP_1588_CLOCK. Fix:
Package kmod-iavf is missing dependencies for the following libraries:
ptp.ko
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
cryptd has been decoupled from crypto-misc in the 6.18 kernel. Fix:
ERROR: module '/home/runner/work/Actions_/Actions_/openwrt/build_dir/target-i386_pentium4_musl/linux-x86_generic/linux-6.18.20/crypto/cryptd.ko' is missing.
make[3]: *** [modules/crypto.mk:873: /home/runner/work/Actions_/Actions_/openwrt/bin/targets/x86/generic/packages/kmod-crypto-misc-6.18.20-r1.apk] Error 1
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22730
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This patch set introduces support for using the in-tree (mainline)
EIP93 crypto driver for kernel 6.18 and later, along with additional
improvements and fixes:
- Conditional Kconfig/Makefile handling for crypto-hw-eip93 to enable use of the mainline driver with kernel 6.18+.
- Patch 926: Use software AES fallback for small requests in the EIP93 driver.
- Patch 927: Add `mediatek,mtk-eip93` compatible string for upstream kernel device trees.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/21078
Signed-off-by: Robert Marko <robimarko@gmail.com>
Rosen Penev
Jonas Jelonek
Marius Dinu
Joshua Covington
Andris PE
Lech Perczak
Mieczyslaw Nalewaj
Qingfang Deng
Thomas Richard
Martin Schiller
Alexandru Gagniuc
Dee HY
Daniel Golle
Raylynn Knight
Ryan Leung
Felix Fietkau
Paweł Owoc
Philip Prindeville
Andrew LaMarche
Zoltan HERPAI
Tianling Shen
Nick Hainke
Tan Zien
Shiji Yang
John Audia
Til Kaiser