The initial bringup missed two GPIO-related settings:
- TX Disable GPIO for the SFP modules
- LED Sync GPIO selection for the port LEDs
This adds the missing TX Disable GPIOs and muxes GPIO18 to LED sync
(there are HC595 shift registers on the board that require the sync).
Signed-off-by: Andreas Böhler <dev@aboehler.at>
Link: https://github.com/openwrt/openwrt/pull/22551
Signed-off-by: Robert Marko <robimarko@gmail.com>
Some new DRM kernel modules appeared in the 6.18 kernel and
are now prompting for selection when enabling DRM in the kernel.
The Gemini D-Link DIR-685 is always the first to run into this
problem hence let's fix it before someone else tries to enable
DRM.
Link: https://github.com/openwrt/openwrt/pull/22875
Signed-off-by: Linus Walleij <linusw@kernel.org>
Specification:
* CPU: MediaTek MT7628AN (580 MHz)
* Flash: GigaDevice GD25Q128CSIG (16 MiB)
* RAM: Winbond W9751G6KB-25 (64 MiB)
WikiDevi page: <https://wikidevi.wi-cat.ru/Keenetic_City_(KN-1510)>
How to flash:
* Configure TFTP server with IP address 192.168.1.2/24
* Serve OpenWrt factory image as "KN-1510_recovery.bin"
* Connect the PC to router's LAN port, hold the reset button and power
the router up. When the power LED starts blinking release the
button.
The same instructions apply to OEM firmware, except one can take it
from osvault.keenetic.net
Signed-off-by: Ivan Davydov <lotigara@lotigara.ru>
Link: https://github.com/openwrt/openwrt/pull/22404
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Specification:
The device is similar to the M30 but has only one LAN port and no WAN port.
- MT7981 CPU using 2.4GHz and 5GHz WiFi (both AX)
- 512MB RAM
- 128MB NAND flash with two UBI partitions with identical size
- 1 multi color LED (red, green, blue, white) connected via GCA230718
- 2 buttons (WPS, reset, LED)
- 1 1Gbit LAN port
Disassembly:
- There are two screws at the power connector which must be removed. Afterwards the top case can be removed (it is clipped on, so some tools are required).
Serial Interface:
- The serial interface can be connected to the 4 pin holes on the board. Do NOT connect VCC.
- The pins are labelled on the PCB (RX, TX, GND)
- Settings: 115200, 8N1
MAC addresses:
- LAN MAC is stored in partition "Odm" at offset 0x8f
- WLAN MAC (2.4 GHz and 5GHz) is LAN MAC + 1
Reverting back to OEM firmware:
- There is currently no easy way to revert back to the OEM image
- The methods from M30 and M60 doesn't seem to work anymore
- If you plan to revert back to OEM firmware later, do the following steps before flashing OpenWrt:
- Boot from initramfs as described in "Flashing via U-Boot" but don't flash anything
- Instead, make a backup of UBI and UBI1 partition
- The created dumps must be written to the initial partitions to revert back to OEM
Flashing via Recovery Web Interface:
- Set your IP address to 192.168.200.10, subnetmask 255.255.255.0
- Press the reset button while powering on the device
- Keep the reset button pressed until the LED blinks red
- Open a Chromium based and goto http://192.168.200.50/ (recovery web interface)
- Download openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-recovery.bin
- Note: The recovery web interface always reports successful flashing, even if it fails
- After flashing, the recovery web interface will try to forward the browser to 192.168.0.1 (can be ignored)
- If flashing was successful, OpenWrt is accessible via 192.168.1.1
- The recovery image boots an initramfs image, flash the sys upgrade image to get to „normal“ OpenWrt mode
Flashing via U-Boot:
- Open the case, connect to the UART console
- Set your IP address to 192.168.200.2, subnet mask 255.255.255.0. Connect to one of the LAN interfaces of the router
- Run a tftp server which provides openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-initramfs-kernel.bin
- Supply the board with 12V
- Select "7. Load image" in the U-Boot menu
- Enter image file, tftp server IP and device IP (if they differ from the default).
- TFTP download to RAM will start. After a few seconds OpenWrt initramfs should start
- The initramfs is accessible via 192.168.1.1, change your IP address accordingly (or use multiple IP addresses on your interface)
- Perform a sysupgrade using openwrt-mediatek-filogic-dlink_aquila-pro-ai-e30-a1-squashfs-sysupgrade.bin
- Reboot the device. OpenWrt should start from flash now
Flashing via OEM web interface is not possible, as it will change the active partition and OpenWrt is only running on the first UBI partition.
Signed-off-by: Roland Reinl <reinlroland+github@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22776
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Replace conditional "LINUX_6_12:mod" / "!LINUX_6_12:mod" AUTOLOAD entries
with version-filtered module names using @lt6.18 / @ge6.18. This makes
version_filter emit plain module names into /etc/modules.d(e.g. "crc32c_generic"),
allowing kmodloader to find and load the correct module for the running kernel.
Fixes crc32c (and related crypto modules) not being autoloaded on 6.12 kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
EDUP EP-RT2983 comes with a factory installed version of OpenWrt 23.05
with device name "netis,n6".
Specification
--------------
- SoC : MediaTek MT7621AT, MIPS, 880 MHz
- RAM : 256 MiB
- Flash : NAND 128 MiB (Toshiba)
- WLAN : MT7905DAN + MT7975DN
- 2.4 GHz : b/g/n/ax, 574 Mbps, MIMO 2x2
- 5 GHz : a/n/ac/ax, 1201 Mbps, MIMO 2x2
- Ethernet : 10/100/1000 Mbps x4 (1x WAN, 3x LAN)
- UART : 3.3V, 115200n8
- Buttons : 1x Reset
1x WPS
- LEDs : 1x Power (green)
1x WiFi (green)
1x Mesh/WPS (green); flashing green during boot
3x LAN (green)
1x WAN (green); flashing red during upgrade and failsafe
- Power : 12 VDC 1A
Installation
-------------
1. Log in to LuCI
2. Go to System, Backup / Flash Firmware
3. If desired, backup the current system by saving (all) the mtdblock
contents.
4. Flash new firmware image, select Flash image.
5. Browse and select the sysupgrade file
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-sysupgrade.bin"
and then Upload.
6. Unselect "Keep settings and retain the current configuration"
Note: All settings will be reset to default. WiFi is not enabled by
default so a connection via Ethernet is necessary to log in and set up.
7. Allow "Force upgrade" (tick the box if there is one), or press Continue
if there is no box to tick. This is because the name is now
"edup,ep-rt2983" as it should have been from the start.
8. Proceed to flash. Wait for reboot and keep power connected.
9. After reboot, default address to access LuCI is 192.168.1.1 with
no password
Recovery (UART)
----------------
1. Remove the 4 screws on the bottom and pry open the cover.
2. Connect serial adapter to the unpopulated serial header pins
TX, RX, GND near the WPS button. Do not connect VCC.
3. Start serial terminal (e.g. minicom, screen, etc) on the computer and
turn on the router.
4. As prompted, hit any key to stop autoboot.
5. Enter 2 to select "2. Upgrade firmware"
6. Enter 0 to select "0 - TFTP client (Default)"
7. Accept the defaults by pressing Enter for
"Input U-Boot's IP address: 192.168.1.1",
"TFTP server's IP address: 192.168.1.2",
"Input IP netmask: 255.255.255.0"
8. Assign your PC's Ethernet port a static IP 192.168.1.2 with netmask
255.255.255.0 and connect to a LAN port on the router using the
Ethernet cable. Disconnect all other network connections (e.g. WiFi) on
the computer.
9. Serve the factory image
"openwrt-*-ramips-mt7621-edup_ep-rt2983-squashfs-factory.bin" using
a TFTP server, e.g. tftpd64. For convenience, the filename can be renamed
to something shorter.
10. In the serial terminal, when prompted "Input file name:", enter the
filename from the previous step and press Enter.
11. The factory image will be flashed as indicated. Wait for reboot.
MAC addresses prototype
------------------------
+---------+---------------------+
| | MAC example |
+---------+---------------------+
| LAN | CC:D8:1F:47:xx:yy |
| WAN | CC:D8:1F:47:xx:yy+1 |
| WLAN 2G | CC:D8:1F:17:xx:yy+2 |
| WLAN 5G | CC:D8:1F:77:xx:yy+2 |
+---------+---------------------+
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/22197
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
For some unknown reason carving out the mdio bus from the ethernet
node forgot the TP-Link SG2452P. The notation still reads
ðernet0 {
mdio: mdio-bus {
compatible = "realtek,rtl838x-mdio";
...
Like everywhere else it should be
&mdio_bus0 {
PHY_C22(0, 0)
...
Fix that.
Fixes: 57b270684 ("rearrange mdio-bus below mdio-controller")
Signed-off-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Link: https://github.com/openwrt/openwrt/pull/22866
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The pinmux entry for disabling JTAG includes a comment which points to
which GPIOs are sacrificed for using JTAG. However, this comment so far
was only aware of GPIO6 and GPIO7. From RTL931X application notes and
datasheets we know which GPIOs are actually affected here.
Extend the comment to include GPIOs 3-5 too.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Add a recipe 'rt-loader-bootbase' to build an image with rt-loader for
devices using the Zyxel BootBase/BootExtension chain. They need a plain
bootable image for initramfs (preferably rt-loader with piggy-backed
uImage) and a plain uImage for flashing. The flashable uImage is later
combined with the loader into a signed/checksummed image.
This template recipe can be used directly for GS1920-24HP, making the
initramfs image more flexible due to using uImage instead of plain
image.
Suggested-by: Markus Stockhausen <markus.stockhausen@gmx.de>
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22827
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This is based on version 1.0.93 plus these commits:
0ca689a fix: fetch base branch to ensure correct PR-only diffs
b7d533d fix: handle fork PRs by fetching via pull/N/head
Link: https://github.com/openwrt/openwrt/pull/22897
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
track_progress: true makes Claude post an initial comment immediately
when triggered and update it with a checklist as it works, so reviewers
can see what Claude is doing rather than waiting for a silent delay.
It also forces tag mode on PR/issue comment events, which is the
correct mode for interactive code review.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Link: https://github.com/openwrt/openwrt/pull/22897
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Allow Bash(grep:*) so Claude can search the codebase for context
during PR reviews. Without this, grep calls using shell glob patterns
were denied even though plain directory greps were allowed.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Link: https://github.com/openwrt/openwrt/pull/22897
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The workflow already uses contents: read which prevents GitHub from
accepting any push. The --disallowedTools setting adds a second layer
by stopping Claude from even attempting git write operations.
Co-Authored-By: Claude Sonnet 4.6 <noreply@anthropic.com>
Link: https://github.com/openwrt/openwrt/pull/22897
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The GitHub CI was sometimes still building some tools again even when
the same version was already pre-built. This change fixes the problem
and should improve the speed of the GitHub CI actions. The duration of
the "Build tools" step will be reduced from 5 to 20 minutes down to
10 to 15 seconds.
make also checks that dependencies are not more recent than the target
it wants to build. Previously find returned files in an arbitrary order
and touch set the current timestamp. Since touch is called per file the
timestamps differ in fractional seconds, so not all files got the same
time. make detected a more recent dependency and started to rebuild.
Now all files are set to the same timestamp and make will assume
everything is up to date.
It is sufficient to only touch the stamp files to prevent rebuilding.
Link: https://github.com/openwrt/openwrt/pull/22888
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The defconfig file used to build tools is "tools-only_defconfig".
Though u-boot scripts can still automatically handle the old style
name for compatibility reason, it's better to use the correct name.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22844
Signed-off-by: Nick Hainke <vincent@systemli.org>
CONFIG_PAGE_BLOCK_MAX_ORDER was set to 10 as the page size is 4k.
All other kernel symbols are automatically refreshed by
`make kernel_oldconfig CONFIG_TARGET=target` and
`make kernel_oldconfig CONFIG_TARGET=subtarget`.
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22771
Signed-off-by: Nick Hainke <vincent@systemli.org>
Andreas Böhler
Linus Walleij
Paul Spooren
Hiroki Utsunomiya
Ivan Davydov
Roland Reinl
Qingfang Deng
Luiz Angelo Daros de Luca
Rosen Penev
Mieczyslaw Nalewaj
Ryan Leung
Richard Huynh
Markus Stockhausen
Jonas Jelonek
Hauke Mehrtens
Shiji Yang
John Audia