This commit fixes "286f377389a button-hotplug: add KEY_SETUP and KEY_VENDOR
handling" which changed the code without bumping the PKG_RELEASE, resulting in
different binaries under the same version.
Signed-off-by: Paul Spooren <mail@aparcar.org>
Link: https://github.com/openwrt/openwrt/pull/23826
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Backport two upstream commits that replace memset() on coherent DMA
descriptor rings with explicit WRITE_ONCE() status word stores.
On 32-bit PowerPC platforms like apm821xx, coherent DMA memory may be
mapped uncached. The optimized memset() path can use dcbz there, which
triggers alignment warnings and spams the kernel log.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23776
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
LED trigger for network interfaces.
- Aggregated per-family (lan/wan/wlan).
- Family and flags are taken from device tree properties:
- "family" : simple family string "lan" | "wan" | "wlan"
- "mode" : any combination of "link", "tx", "rx" flags
Priority/combination:
* If "mode" present: flags come from "mode" and take precedence.
Family is taken from "family" if present, otherwise from the LED name.
* If only "family" present: use its family and default flags = link+tx+rx.
* If neither present: fall back to LED device name parsing.
- Suffix "-online" is valid ONLY in the LED name (label),
e.g. "green:wlan-online". It indicates the online variant but is applied
only when DT "mode" is absent.
Behaviour:
- wlan (normal): blink/solid driven by throughput table
- lan/wan (normal): one-shot blink on TX/RX packet change
- *-online variants: steady ON while any interface of the family has carrier
Interfaces are auto-tracked by name match (lan0, wan1, wlan2, phy0, wl1,
ath0, ra0...). Up to MAX_IFACES (16) interfaces per family
This trigger is intended for board/device authors and drivers to provide simple
network-activity LED behaviour without per-interface wiring in userspace.
Refresh bcm27xx patches in the same commit to account for line shifts in
drivers/leds/trigger/Kconfig and Makefile, ensuring clean applies for
bisectability.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/19903
Signed-off-by: Robert Marko <robimarko@gmail.com>
c3bf07a66f7e make: honor SOURCE_DATE_EPOCH in BUILD_DATE
bb4f3f0b947e Revert "MP: fix uniphy reset in phy to phy link scenario"
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add support for the Micro Crystal RV3028 I2C real-time clock chip.
Tested on a Kontron OSM-S/BL i.MX8MP eval board.
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Since upstream commit 60e3f1e9b7a5 ("lib/crypto: arm64/sha512:
Migrate optimized SHA-512 code to library"), the kernel module is no
longer available, and its fucntionality os provided by the kernel
core. Thus do not try to package this for linux 6.18 and later.
Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/21506
Signed-off-by: Robert Marko <robimarko@gmail.com>
Add a function to allow drivers to query the pending AQL airtime
for a given txq, for both unicast and broadcast.
This will be used for mt76 to limit buffering in AP mode for power-save
stations.
Signed-off-by: Felix Fietkau <nbd@nbd.name>
gpio-button-hotplug skips buttons with button->irq set because it cannot
handle true interrupt-only gpio-keys descriptions. That check also skips
valid GPIO-backed buttons that provide a separate interrupt specifier, such
as the Meraki MX60 reset button.
Try to acquire the GPIO descriptor before deciding that an explicit-IRQ
button is unsupported. Continue to skip true interrupt-only buttons, and
make the IRQ setup and teardown paths ignore skipped entries.
Tested on: Cisco Meraki MX60. Reset button now works.
Fixes: 23845fa10b ("gpio-button-hotplug: do not error on interrupt attached keys")
Assisted-by: Codex:GPT-5.5
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23382
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The AddDepends/pse-pd helper appended kmod-pse-pd to DEPENDS without the
'+' prefix, making it a hard dependency rather than an auto-selecting one.
This breaks pulling any PSE controller driver (kmod-pse-pd692x0,
kmod-pse-si3474, kmod-pse-tps23881, kmod-pse-regulator, ...) in via a
device's DEVICE_PACKAGES: the kmod itself is auto-selected, but the
unsatisfied hard dep on kmod-pse-pd silently drops it from .config.
Prefix the kmod-pse-pd entry with '+' so it auto-selects, matching how
the other deps in the same file (kmod-i2c-core, etc.) are expressed. The
helper is the right place to fix this; every PSE controller driver routes
through it.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23449
Signed-off-by: Robert Marko <robimarko@gmail.com>
OSLEC has been dropped upstream since Linux 6.16.
Reflect that by no longer providing the kernel module package
`kmod-echo` which essentially became an empty stub.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This improves on openwrt/openwrt@aeb9028aab by adding support for
other Dell EMC Edge620/640/680 devices and mapping
the interfaces to match the markings on the device.
This modifies the netdevices.mk file to set the boot flag for
ixgbe driver to load it in early stage of the boot process to
allow for proper mapping of the network interface PCI paths
inside the 02_network script. This will also allow other devices
using the ixgbe driver to do proper mapping in 02_network script.
The 02_network script is then modified to support all
dell-emc-620/640/680 devices. It now maps the network
interfaces via PCI paths to match the markings on the device.
The interface marked GE6 is still used for WAN with
interfaces GE1-GE5 used for LAN.
The SFP1 and SFP2 interfaces are left to be assigned by
the user.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/23110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Select `CONFIG_ROCKCHIP_SARADC=y` to enable Rockchip SAR ADC
Add ADC Ladder Buttons driver as a kernel module as well as `kmod-button-hotplug` to the list of
default packages for Rockchip targets that have buttons connected to ADC, not including some
devices (e.g. NanoPi R76S) that have ADC buttons which are not in the device tree.
This is needed to use buttons on Rockchip devices that are connected to ADC and not GPIO
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-sound-midi2 expects sound/core/snd-ump.ko, but
CONFIG_SND_UMP=y builds it in-kernel rather than as
a module. Replace the forced built-in setting with
plain CONFIG_SND_UMP so the module can be packaged
correctly.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23265
Signed-off-by: Robert Marko <robimarko@gmail.com>
This contains many fixes from upstream Linux.
The code block from this patch was moved a bit in the function:
subsys/110-mac80211_keep_keys_on_stop_ap.patch
This patch was applied upstream:
subsys/330-mac80211-fix-crash-in-ieee80211_chan_bw_change-for-A.patch
Link: https://github.com/openwrt/openwrt/pull/23167
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Fix dependency for kmod-drm-client-lib module:
error: recursive dependency detected!
symbol LINUX_6_18 is selected by PACKAGE_kmod-drm-client-lib
symbol PACKAGE_kmod-drm-client-lib is selected by LINUX_6_18
Fixes: e75ba35ed8 ("modules: video: introduce DRM client setup module")
Signed-off-by: Paweł Owoc <frut3k7@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23124
Signed-off-by: Robert Marko <robimarko@gmail.com>
Linux commit c9e5ac0 ("lib/crypto: mips/md5: Migrate optimized code into
library") removed the MIPS-Octeon-specific MD5 implementation
(octeon-md5.ko) and replaced it with an optimized library implementation
in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_OCTEON and the module
arch/mips/crypto/octeon-md5.ko no longer exist in kernels >= 6.18.
Signed-off-by: Andrew LaMarche <andrewjlamarche@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23031
Signed-off-by: Nick Hainke <vincent@systemli.org>
6.14 has introduced a DRM client setup library. Add kmod-drm-client-lib
to support it, and add it as a dependency to DRM modules which depend on it.
Link: https://github.com/openwrt/openwrt/pull/22975
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
Motorcomm YT6801 is a PCIe ethernet controller based on DWMAC4 IP. It
integrates an GbE phy, supporting WOL, VLAN tagging and various types
of offloading. It ships an on-chip eFuse for storing various vendor
configuration, including MAC address.
The PM and plat_data functions were slightly modified to build with
current kernel.
Signed-off-by: Tianling Shen <cnsztl@immortalwrt.org>
Link: https://github.com/openwrt/openwrt/pull/22923
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Linux commit 09371e1349c9 ("lib/crypto: powerpc/md5: Migrate optimized code into library")
removed the PowerPC-specific MD5 implementation (md5-ppc.ko) and
replaced it with an optimized library implementation in lib/crypto.
As a result, CONFIG_CRYPTO_MD5_PPC and the module
arch/powerpc/crypto/md5-ppc.ko no longer exist in kernels >= 6.18.
Link: https://github.com/openwrt/openwrt/pull/22732
Signed-off-by: Nick Hainke <vincent@systemli.org>
Fixes:
ifxmips_aes.c: In function 'gcm_aes_decrypt':
ifxmips_aes.c:1803:14: error: assignment discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1803 | temp = walk.src.virt.addr;
| ^
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22921
Signed-off-by: Robert Marko <robimarko@gmail.com>
Fixes:
ltq_atm.c: In function 'ltq_atm_probe':
ltq_atm.c:1840:36: error: passing argument 2 of 'platform_set_drvdata' discards 'const' qualifier from pointer target type [-Werror=discarded-qualifiers]
1840 | platform_set_drvdata(pdev, ops);
| ^~~
In file included from ltq_atm.c:40:
/workspaces/openwrt/build_dir/target-mips_24kc_musl/linux-lantiq_xway/linux-6.18.21/include/linux/platform_device.h:276:47: note: expected 'void *' but argument is of type 'const struct ltq_atm_ops *'
276 | void *data)
| ~~~~~~^~~~
Fixes: c1fa85f659 ("treewide: use of_device_get_match_data")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/22921
Signed-off-by: Robert Marko <robimarko@gmail.com>
Replace conditional "LINUX_6_12:mod" / "!LINUX_6_12:mod" AUTOLOAD entries
with version-filtered module names using @lt6.18 / @ge6.18. This makes
version_filter emit plain module names into /etc/modules.d(e.g. "crc32c_generic"),
allowing kmodloader to find and load the correct module for the running kernel.
Fixes crc32c (and related crypto modules) not being autoloaded on 6.12 kernels.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/22798
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Paul Spooren
Rosen Penev
Qingfang Deng
Thomas Richard
Mieczyslaw Nalewaj
Robert Marko
Martin Schiller
Alexandru Gagniuc
Felix Fietkau
Dee HY
Daniel Golle
Jonas Jelonek
Ryan Leung
Andy Chiang
Raylynn Knight
Shiji Yang
Til Kaiser
Hauke Mehrtens
Paweł Owoc
Philip Prindeville
Andrew LaMarche
Zoltan HERPAI
Tianling Shen
Nick Hainke