Shine- GH
4e16c2ed8f
The Netgear GS110TPv3 is a 10-port gigabit managed switch with 8x RJ45
ports and 2x SFP cages. All 8x RJ45 ports are PoE+ capable.
This switch is similar to the already supported GS108Tv3 and GS110TPP
models and even shares its stock firmware with these two. SFP cage
configuration, on the other hand, is identical to the GS310TP.
SoC: RTL8380M, 500MHz
RAM: 128MB DDR3
Flash: 32MB SPI-NOR
Ethernet: 8x 1GBE RJ45
2x 1GBE SFP Cages
PoE: 8x PoE+ via Nuvoton controller, 55W total power budget
UART: onboard, unpopulated (J1), 115200/8N1, 3.3V
LEDs: 1x dual color green/amber power LED, GPIO controlled
1x amber PoE-Max and 8x green/amber PoE port LEDs
- handled by PoE controller
8x green/amber port status LEDs, unsupported in OpenWrt
- handled by RTL8231 GPIO expander (see install instructions)
MAC address: base MAC from "ethaddr" U-Boot env variable, additional port
MACs assigned incrementally.
Installation instructions:
1. Install OpenWrt initramfs firmware to the "Image1" firmware slot via
vendor web GUI.
2. If not already so, set next startup firmware to "Image1" ("Activate"),
then reboot.
3. After booting into OpenWrt initramfs firmware, access the device at IP
192.168.1.1 and install the OpenWrt sysupgrade image.
4. Device automatically reboots once again into OpenWrt.
5. (Optional) To enable default port LED handling, change boot command by
running in OpenWrt CLI: fw_setenv bootcmd "rtk network on; boota"
Note: This may cause VLAN leaking during boot.
Back to stock:
1. Reset boot command to stock: "fw_setenv bootcmd boota"
2. Change to secondary firmware partition: "fw_setsys bootpartition 1"
3. Reboot. Device will now boot into stock firmware.
3. (Optional) Revert to stock firmware also for "Image1" firmware slot via
vendor web GUI.
Signed-off-by: Shine- GH <4c.fce2@proton.me>
Link: https://github.com/openwrt/openwrt/pull/26006
Signed-off-by: Jonas Jelonek <jonas@jonasjelonek.de>
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.8+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0