Daniel Golle
ba45d608b2
The Herospeed RV1126 IMX415 "Base" is an IP camera built on a Rockchip 38x38 V10 EMMC DDR3 board, which is also found in cameras of other makes and is therefore described by a separate dtsi. The stock firmware identifies itself as ONVIF manufacturer "HeroSpeed", firmware family RV1126_IMX415_BASE. This adds the 32-bit armv7 subtarget for the Cortex-A7 based RV11xx SoCs. The camera keeps its stock U-Boot, which boots an Android boot image from one of two boot/system slots. Hardware -------- SoC: Rockchip RV1126, 4x Cortex-A7 RAM: 1 GiB DDR3 Flash: eMMC, 8 GB class, two boot/system slots Ethernet: 1x 10/100 Mbit/s, JL1101 PHY on RMII Sensor: Sony IMX415, 4 lane MIPI CSI-2 RTC: PCF8563 LEDs: white illumination LEDs on one PWM output (V4L2 flash) Buttons: none UART: 1.8 V TTL on UART2, 1500000 baud 8N1, 90-degree JST-SH connector at the bottom edge of the board, facing the edge and hidden underneath the MIPI CSI cable Power: PoE (IEEE 802.3af) or 12 V 1 A DC through the barrel connector on the cable whip Installation ------------ 1. Open the web interface of the stock firmware (192.168.1.168 by default) and log in as admin. 2. Upload openwrt-rockchip-armv7-herospeed_rv1126-imx415-squashfs- factory-RV1126_IMX415.fls on the firmware upgrade page. 3. The camera reboots into OpenWrt at 192.168.1.1. Later upgrades use the sysupgrade image, which is written to the inactive slot. The stock firmware can be restored from OpenWrt with "sysupgrade -F -n" and the original .FLS file. MAC address ----------- eth0 uses the label MAC, stored as MAC=xx:xx:xx:xx:xx:xx in net.conf on the ext4 "param" partition. U-Boot passes a different, derived address to Linux, which is replaced by the stored one. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.8+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0