David Evans
c8c2dfc30e
The GS1920-24 v1 is the non-PoE, fanless sibling of the already supported GS1920-24HP v1 (ZyNOS firmware code AAOB vs. AAOC) and shares its board layout and flash map. Hardware: * SoC: Realtek RTL8392M * Flash: 16 MiB SPI NOR (Macronix MX25L12835F) * RAM: 128 MiB DDR3 * Ethernet: 24x 10/100/1000BASE-T (3x RTL8218B), 4x combo RJ45/SFP (RTL8214FC) * Hardware monitor: Analog Devices ADT7463C * LEDs: PWR, SYS, ALM, LOCATOR, per-port link/activity * Buttons: 1x reset (front) * UART: RS-232 level (not TTL) on header J2, DCE pinout (Tx pin 2, Rx pin 3, GND pin 5), 9600 8N1 * Power: 100-240 V AC, 50/60 Hz, 25.9 W max * No PoE, no fan MAC address: * Ethernet: factory MAC from the bootbase partition at offset 0x1fff8 through the factory_macaddr nvmem cell * ethernet0 is the label MAC device; 02_network uses this address for the LAN/bridge without assigning individual per-port MAC addresses The hardware monitor at I2C address 0x2e was identified on hardware as an ADT7463C from company ID 0x41 and VERSTEP 0x6a. The GS1920-24HP v1 uses an ADT7468, while the v2 uses an lm85-family hardware monitor at the same address. All GS1920-24 variants use hardware monitors supported by kmod-hwmon-lm85. The shared GS1920 device recipe therefore supplies that package, while the GS1920-24HP-specific recipe additionally supplies the PSE driver. Installation: 1. Connect to the console. Optionally switch BootBase to 115200 baud with ATBA5 (and reconnect at that rate). 2. Load an initramfs image into RAM: ATUP80100000, send the image via XMODEM, then ATGO80100000. 3. Copy loader.bin and the sysupgrade image to /tmp on the running initramfs system. 4. Flash both: mtd write /tmp/loader.bin loader mtd write /tmp/*-squashfs-sysupgrade.bin firmware 5. Reboot. The SFP side of the combo ports is untested (no modules available); the copper side of all 28 ports works. Tested on hardware: Flash installation and runtime operation verified. Signed-off-by: David Evans <git@d4vid.uk> Link: https://github.com/openwrt/openwrt/pull/24962 Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
OpenWrt Project is a Linux operating system targeting embedded devices. Instead of trying to create a single, static firmware, OpenWrt provides a fully writable filesystem with package management. This frees you from the application selection and configuration provided by the vendor and allows you to customize the device through the use of packages to suit any application. For developers, OpenWrt is the framework to build an application without having to build a complete firmware around it; for users this means the ability for full customization, to use the device in ways never envisioned.
Sunshine!
Download
Built firmware images are available for many architectures and come with a package selection to be used as WiFi home router. To quickly find a factory image usable to migrate from a vendor stock firmware to OpenWrt, try the Firmware Selector.
If your device is supported, please follow the Info link to see install instructions or consult the support resources listed below.
An advanced user may require additional or specific package. (Toolchain, SDK, ...) For everything else than simple firmware download, try the wiki download page:
Development
To build your own firmware you need a GNU/Linux, BSD or macOS system (case sensitive filesystem required). Cygwin is unsupported because of the lack of a case sensitive file system.
Requirements
You need the following tools to compile OpenWrt, the package names vary between distributions. A complete list with distribution specific packages is found in the Build System Setup documentation.
binutils bzip2 diff find flex gawk gcc-6+ getopt grep install libc-dev libz-dev
make4.1+ perl python3.8+ rsync subversion unzip which
Quickstart
-
Run
./scripts/feeds update -ato obtain all the latest package definitions defined in feeds.conf / feeds.conf.default -
Run
./scripts/feeds install -ato install symlinks for all obtained packages into package/feeds/ -
Run
make menuconfigto select your preferred configuration for the toolchain, target system & firmware packages. -
Run
maketo build your firmware. This will download all sources, build the cross-compile toolchain and then cross-compile the GNU/Linux kernel & all chosen applications for your target system.
Related Repositories
The main repository uses multiple sub-repositories to manage packages of
different categories. All packages are installed via the OpenWrt package
manager called opkg. If you're looking to develop the web interface or port
packages to OpenWrt, please find the fitting repository below.
-
LuCI Web Interface: Modern and modular interface to control the device via a web browser.
-
OpenWrt Packages: Community repository of ported packages.
-
OpenWrt Routing: Packages specifically focused on (mesh) routing.
-
OpenWrt Video: Packages specifically focused on display servers and clients (Xorg and Wayland).
Support Information
For a list of supported devices see the OpenWrt Hardware Database
Documentation
Support Community
- Forum: For usage, projects, discussions and hardware advise.
- Support Chat: Channel
#openwrton oftc.net.
Developer Community
- Bug Reports: Report bugs in OpenWrt
- Dev Mailing List: Send patches
- Dev Chat: Channel
#openwrt-develon oftc.net.
License
OpenWrt is licensed under GPL-2.0