mirror of
https://github.com/openwrt/openwrt.git
synced 2026-06-17 17:01:44 +04:00
mediatek: add Huasifei WH3000R NAND support
**Huasifei WH3000R NAND** Wi-Fi 6 router based on MediaTek MT7981B SoC. MT7981B+MT7976CN+MT7531AE **Specifications** SoC: Filogic 820 MT7981B (1.3GHz) RAM: DDR3 512MB Flash: 256MiB Winbond SPI NAND WiFi: MT7976C: 2.4GHz 2x2, 5GHz 2x2 Ethernet: MT7531: 3x 1GbE LAN + 1x 1GbE WAN USB: 1x USB 3.0 port Two buttons: reset and mesh LEDs: RGB (red, green, blue together) UART: 3.3V, TX, RX, GND / 115200 8N1 DC power interface +---------+-------------------+--------------------------+ | | MAC | Algorithm | +---------+-------------------+--------------------------+ | LAN | 58:23:BC:xx:xx:x2 | label+1 | | WAN | 58:23:BC:xx:xx:x1 | label+0 (eeprom) | | WLAN 2g | 58:23:BC:xx:xx:x3 | label+2 | | WLAN 5g | 58:23:BC:xx:xx:x4 | label+3 | +---------+-------------------+--------------------------+ Since it's convenient for the users to check and tell MAC to their internet providers from the router label, we set WAN as a base MAC located at 'Factory', 0x4. Discussed this with the vendor. **Installation via U-Boot rescue** 1. Set static IP 192.168.1.2 on your computer and default route as 192.168.1.1 2. Connect to the LAN port and hold the reset button while booting the device. 3. Wait for the LED to blink 5 times, and release the reset button. 4. Open U-boot web page on your browser at http://192.168.1.1 5. Select the OpenWrt sysupgrade image, upload it, and start the upgrade. 6. Wait for the router to flash the new firmware. 7. Wait for the router to reboot itself. **Installation via sysupgrade** Just flash sysupgrade file via [LuCI upgrade page](http://192.168.1.1/cgi-bin/luci/admin/system/flash) without saving the settings. **Installation via SSH** Upload the file to the router `/tmp` directory, `ssh root@192.168.1.1` and issue a command: ``` sysupgrade -n /tmp/openwrt-mediatek-filogic-huasifei_wh3000r-nand-squashfs-sysupgrade.bin ``` Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com> Link: https://github.com/openwrt/openwrt/pull/23156 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit is contained in:
Fil Dunsky
committed by
Hauke Mehrtens
Hauke Mehrtens
parent
db7d264e47
commit
b2795a7908
@@ -0,0 +1,292 @@
|
||||
// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
|
||||
|
||||
/dts-v1/;
|
||||
#include <dt-bindings/gpio/gpio.h>
|
||||
#include <dt-bindings/input/input.h>
|
||||
#include <dt-bindings/leds/common.h>
|
||||
|
||||
#include "mt7981b.dtsi"
|
||||
|
||||
/ {
|
||||
model = "Huasifei WH3000R NAND";
|
||||
compatible = "huasifei,wh3000r-nand", "mediatek,mt7981";
|
||||
|
||||
aliases {
|
||||
label-mac-device = &gmac1;
|
||||
|
||||
led-boot = &led_power;
|
||||
led-failsafe = &led_power;
|
||||
led-running = &led_status;
|
||||
led-upgrade = &led_power;
|
||||
|
||||
serial0 = &uart0;
|
||||
};
|
||||
|
||||
chosen {
|
||||
stdout-path = "serial0:115200n8";
|
||||
};
|
||||
|
||||
memory {
|
||||
reg = <0 0x40000000 0 0x20000000>;
|
||||
device_type = "memory";
|
||||
};
|
||||
|
||||
gpio-keys {
|
||||
compatible = "gpio-keys";
|
||||
|
||||
button-mesh {
|
||||
label = "mesh";
|
||||
linux,code = <KEY_RFKILL>;
|
||||
gpios = <&pio 0 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
|
||||
button-reset {
|
||||
label = "reset";
|
||||
linux,code = <KEY_RESTART>;
|
||||
gpios = <&pio 1 GPIO_ACTIVE_LOW>;
|
||||
debounce-interval = <60>;
|
||||
};
|
||||
};
|
||||
|
||||
gpio-leds {
|
||||
compatible = "gpio-leds";
|
||||
|
||||
led_power: led_power {
|
||||
function = LED_FUNCTION_POWER;
|
||||
color = <LED_COLOR_ID_RED>;
|
||||
gpios = <&pio 9 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_status: led_status {
|
||||
function = LED_FUNCTION_STATUS;
|
||||
color = <LED_COLOR_ID_GREEN>;
|
||||
gpios = <&pio 10 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
|
||||
led_internet {
|
||||
function = LED_FUNCTION_WAN_ONLINE;
|
||||
color = <LED_COLOR_ID_BLUE>;
|
||||
gpios = <&pio 11 GPIO_ACTIVE_LOW>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
ð {
|
||||
status = "okay";
|
||||
|
||||
gmac0: mac@0 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <0>;
|
||||
phy-mode = "2500base-x";
|
||||
nvmem-cells = <&macaddr_factory_4 1>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
|
||||
gmac1: mac@1 {
|
||||
compatible = "mediatek,eth-mac";
|
||||
reg = <1>;
|
||||
phy-mode = "gmii";
|
||||
nvmem-cells = <&macaddr_factory_4 0>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
phy-handle = <&phy0>;
|
||||
label = "wan";
|
||||
};
|
||||
|
||||
mdio: mdio-bus {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
phy0: ethernet-phy@0 {
|
||||
compatible = "ethernet-phy-id03a2.9461";
|
||||
reg = <0>;
|
||||
phy-mode = "gmii";
|
||||
nvmem-cells = <&phy_calibration>;
|
||||
nvmem-cell-names = "phy-cal-data";
|
||||
};
|
||||
|
||||
switch: switch@1f {
|
||||
compatible = "mediatek,mt7531";
|
||||
reg = <0x1f>;
|
||||
reset-gpios = <&pio 39 GPIO_ACTIVE_HIGH>;
|
||||
interrupt-controller;
|
||||
#interrupt-cells = <1>;
|
||||
interrupt-parent = <&pio>;
|
||||
interrupts = <38 IRQ_TYPE_LEVEL_HIGH>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&spi0 {
|
||||
pinctrl-names = "default";
|
||||
pinctrl-0 = <&spi0_flash_pins>;
|
||||
status = "okay";
|
||||
|
||||
spi_nand@0 {
|
||||
compatible = "spi-nand";
|
||||
reg = <0>;
|
||||
|
||||
spi-max-frequency = <52000000>;
|
||||
spi-tx-bus-width = <4>;
|
||||
spi-rx-bus-width = <4>;
|
||||
|
||||
spi-cal-enable;
|
||||
spi-cal-mode = "read-data";
|
||||
spi-cal-datalen = <7>;
|
||||
spi-cal-data = /bits/ 8 <0x53 0x50 0x49 0x4e 0x41 0x4e 0x44>;
|
||||
spi-cal-addrlen = <5>;
|
||||
spi-cal-addr = /bits/ 32 <0x0 0x0 0x0 0x0 0x0>;
|
||||
|
||||
mediatek,nmbm;
|
||||
mediatek,bmt-max-ratio = <1>;
|
||||
mediatek,bmt-max-reserved-blocks = <64>;
|
||||
|
||||
partitions {
|
||||
compatible = "fixed-partitions";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
partition@0 {
|
||||
label = "BL2";
|
||||
reg = <0x0 0x100000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@100000 {
|
||||
label = "u-boot-env";
|
||||
reg = <0x100000 0x80000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@180000 {
|
||||
label = "Factory";
|
||||
reg = <0x180000 0x200000>;
|
||||
read-only;
|
||||
|
||||
nvmem-layout {
|
||||
compatible = "fixed-layout";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <1>;
|
||||
|
||||
eeprom_factory_0: eeprom@0 {
|
||||
reg = <0x0 0x1000>;
|
||||
};
|
||||
|
||||
macaddr_factory_4: macaddr@4 {
|
||||
compatible = "mac-base";
|
||||
reg = <0x4 0x6>;
|
||||
#nvmem-cell-cells = <1>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
partition@380000 {
|
||||
label = "FIP";
|
||||
reg = <0x380000 0x200000>;
|
||||
read-only;
|
||||
};
|
||||
|
||||
partition@580000 {
|
||||
label = "ubi";
|
||||
reg = <0x580000 0xe280000>;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&pio {
|
||||
spi0_flash_pins: spi0-pins {
|
||||
mux {
|
||||
function = "spi";
|
||||
groups = "spi0", "spi0_wp_hold";
|
||||
};
|
||||
|
||||
conf-pu {
|
||||
pins = "SPI0_CS", "SPI0_HOLD", "SPI0_WP";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-up = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
|
||||
conf-pd {
|
||||
pins = "SPI0_CLK", "SPI0_MOSI", "SPI0_MISO";
|
||||
drive-strength = <MTK_DRIVE_8mA>;
|
||||
bias-pull-down = <MTK_PUPD_SET_R1R0_11>;
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&switch {
|
||||
ports {
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
|
||||
port@0 {
|
||||
reg = <0>;
|
||||
label = "lan1";
|
||||
};
|
||||
|
||||
port@1 {
|
||||
reg = <1>;
|
||||
label = "lan2";
|
||||
};
|
||||
|
||||
port@2 {
|
||||
reg = <2>;
|
||||
label = "lan3";
|
||||
};
|
||||
|
||||
port@6 {
|
||||
reg = <6>;
|
||||
ethernet = <&gmac0>;
|
||||
phy-mode = "2500base-x";
|
||||
|
||||
fixed-link {
|
||||
speed = <2500>;
|
||||
full-duplex;
|
||||
pause;
|
||||
};
|
||||
};
|
||||
};
|
||||
};
|
||||
|
||||
&usb_phy {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&uart0 {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&watchdog {
|
||||
status = "okay";
|
||||
};
|
||||
|
||||
&wifi {
|
||||
status = "okay";
|
||||
#address-cells = <1>;
|
||||
#size-cells = <0>;
|
||||
nvmem-cells = <&eeprom_factory_0>;
|
||||
nvmem-cell-names = "eeprom";
|
||||
|
||||
band@0 {
|
||||
reg = <0>;
|
||||
nvmem-cells = <&macaddr_factory_4 2>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
|
||||
band@1 {
|
||||
reg = <1>;
|
||||
nvmem-cells = <&macaddr_factory_4 3>;
|
||||
nvmem-cell-names = "mac-address";
|
||||
};
|
||||
};
|
||||
|
||||
&xhci {
|
||||
status = "okay";
|
||||
};
|
||||
@@ -126,6 +126,9 @@ glinet,gl-xe3000)
|
||||
huasifei,wh3000)
|
||||
ucidef_set_led_netdev "wan" "WAN" "red:wan" "eth1" "link tx rx"
|
||||
;;
|
||||
huasifei,wh3000r-nand)
|
||||
ucidef_set_led_netdev "wan" "WAN" "blue:wan-online" "wan" "link"
|
||||
;;
|
||||
iptime,ax3000q)
|
||||
ucidef_set_led_netdev "wan" "WAN" "amber:wan" "wan" "link tx rx"
|
||||
;;
|
||||
|
||||
@@ -54,6 +54,7 @@ mediatek_setup_interfaces()
|
||||
creatlentem,clt-r30b1-112m|\
|
||||
cudy,wr3000-v1|\
|
||||
globitel,bt-r320|\
|
||||
huasifei,wh3000r-nand|\
|
||||
jcg,q30-pro|\
|
||||
keenetic,kn-3711|\
|
||||
keenetic,kn-3811|\
|
||||
|
||||
@@ -233,6 +233,7 @@ platform_do_upgrade() {
|
||||
cudy,wr3000h-v1|\
|
||||
cudy,wr3000p-v1|\
|
||||
huasifei,wh3000-pro-nand|\
|
||||
huasifei,wh3000r-nand|\
|
||||
jiorouter,ax6000-jidu6101)
|
||||
CI_UBIPART="ubi"
|
||||
nand_do_upgrade "$1"
|
||||
|
||||
@@ -1885,6 +1885,19 @@ define Device/huasifei_wh3000-pro-nand
|
||||
endef
|
||||
TARGET_DEVICES += huasifei_wh3000-pro-nand
|
||||
|
||||
define Device/huasifei_wh3000r-nand
|
||||
DEVICE_VENDOR := Huasifei
|
||||
DEVICE_MODEL := WH3000R
|
||||
DEVICE_VARIANT := NAND
|
||||
DEVICE_DTS := mt7981b-huasifei-wh3000r-nand
|
||||
DEVICE_DTS_DIR := ../dts
|
||||
IMAGE_SIZE := 231936k
|
||||
IMAGE/sysupgrade.bin := sysupgrade-tar | append-metadata
|
||||
DEVICE_PACKAGES := kmod-mt7915e kmod-mt7981-firmware mt7981-wo-firmware \
|
||||
kmod-usb3
|
||||
endef
|
||||
TARGET_DEVICES += huasifei_wh3000r-nand
|
||||
|
||||
define Device/imou_hx21
|
||||
DEVICE_VENDOR := Imou
|
||||
DEVICE_MODEL := HX21
|
||||
|
||||
Reference in New Issue
Block a user