Replace exit(1) on every failure path with return null so callers that
iterate over multiple radios can collect results from the radios that
did succeed instead of aborting on the first one that refuses an
off-channel scan.
Route diagnostics to stderr via warn() so stdout stays clean for
callers parsing JSON output, and include the device name in each
message to disambiguate per-radio failures.
Signed-off-by: John Crispin <john@phrozen.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
1bf2d490484e libfstools: make get_var_from_file() reusable
0b6022439cad mount_root: add kernel parameter to specify the overlay storage name
e600d842ce81 mount_root: add kernel parameter to specify the overlay fileystem type
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
The chunk length is not correct.
Fixes: d2fabb974c ("mediatek: add support for Wavlink WL-WNT100X3 ubootmod")
Signed-off-by: Shiji Yang <yangshiji66@outlook.com>
The generated firmware patches for RealTek's PHYs are host architecture
agnostic. Express this with PKGARCH:=all.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Now that the upstream RealTek PHY driver is patched to support also
the new 5G and 10G PHYs we can start to phase-out the messy downstream
driver.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
This is required by the realtek PHY driver for:
* rtl8261n.bin (package "rtl8261n-firmware" or "rtl8261n-lp-firmware")
- RTL8251L 5Gbps PHY
- RTL8261BE 10Gbps PHY
- RTL8261N 10Gbps PHY
* rtl8264b.bin (package "rtl8264b-firmware")
- RTL8254B 5Gbps PHY
- RTL8264 10Gbps PHY
- RTL8264B 10Gbps PHY
These PHY chips need a sequence of register writes for initialization.
These are provided as firmware files which are interpreted/applied by a
new register patch engine.
For the moment, the patch instructions in rtl8261-firmware and
rtl8264b-firmware are the same as from the rtl8261n driver. This should
make it possible to first evaluate the patch engine and driver development
for switching over in adjusting the patch instructions.
Signed-off-by: Balázs Triszka <info@balika011.hu>
[sven: rebase, split, fix package version/release, use conf from rtl8261n
driver]
Signed-off-by: Sven Eckelmann <sven@narfation.org>
[daniel: define VERSION matching source date for the resulting packages]
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
The AddDepends/pse-pd helper appended kmod-pse-pd to DEPENDS without the
'+' prefix, making it a hard dependency rather than an auto-selecting one.
This breaks pulling any PSE controller driver (kmod-pse-pd692x0,
kmod-pse-si3474, kmod-pse-tps23881, kmod-pse-regulator, ...) in via a
device's DEVICE_PACKAGES: the kmod itself is auto-selected, but the
unsatisfied hard dep on kmod-pse-pd silently drops it from .config.
Prefix the kmod-pse-pd entry with '+' so it auto-selects, matching how
the other deps in the same file (kmod-i2c-core, etc.) are expressed. The
helper is the right place to fix this; every PSE controller driver routes
through it.
Signed-off-by: Jonas Jelonek <jelonek.jonas@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23449
Signed-off-by: Robert Marko <robimarko@gmail.com>
This allows us to use the full size of nand, which increases ubi size
from 90M to 122.25M.
Flashing instructions:
1. Login into the device and backup all your partitions,
especially `Factory` and 'HW' to be able to come back to stock and use all
Wavlink services.
2. Unlock mtd partitions:
```
apk update && apk add kmod-mtd-rw
insmod mtd-rw i_want_a_brick=1
```
3. Upload new `bl2` and `fip` to the router /tmp and write them:
```
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-preloader.bin bl2
mtd write /tmp/openwrt-mediatek-filogic-wavlink_wl-wnt100x3-ubootmod-bl31-uboot.fip fip
mtd erase ubi
```
4. Set static IP on your PC:
IP 192.168.1.254/24, GW 192.168.1.1
5. Serve OpenWrt initramfs image using TFTP server.
6. Cut off the power and re-engage, wait for TFTP recovery to complete.
7. After OpenWrt initramfs has booted, prepare ubi and envs:
```
ubidetach -p /dev/mtd4 && ubiformat /dev/mtd4 -y && ubiattach -p /dev/mtd4 && ubimkvol /dev/ubi0 -n 0 -N ubootenv -s 128KiB && ubimkvol /dev/ubi0 -n 1 -N ubootenv2 -s 128KiB
```
8. Perform sysupgrade.
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22753
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
| Component | Details |
|------------------|-------------------------------------------------|
| **SoC** | MediaTek MT7986A (4× ARM Cortex-A53 @ 2.0 GHz) |
| **RAM** | 512 MB |
| **Flash** | 256 MB NAND |
| **Ethernet** | 5× 10/100/1000 Mbps (1 WAN + 4 LAN) |
| **WLAN 2.4 GHz** | MediaTek MT7976GN — 802.11b/g/n/ax, 4×4 MIMO |
| **WLAN 5 GHz** | MediaTek MT7976AN — 802.11n/ac/ax, 4×4 MIMO |
| **LEDs** | 1× RGB LED (GPIO-controlled) |
| **Button** | 1× Reset |
| **USB** | Yes |
**MAC Addresses:**
| Interface | Source |
|------------|-------------------------------------------------|
| WAN/Label | u-boot-env MTD partition, "mac" (text) |
| LAN | WAN + 1 |
| 2.4 GHz | WAN + 2 |
| 5 GHz | WAN + 3 |
---
**1. Prepare TFTP server**
Set a static IP on the ethernet interface of your computer (e.g. default: ip `192.168.1.2`, gateway `192.168.1.1`).
Download the initramfs image and host it with the TFTP server.
**2. Interrupt boot**
Attach UART and power on the router. When the boot menu appears, select **Failsafe Mode**,
then press `Ctrl-C` to interrupt and enter the U-Boot prompt.
**3. Load and run initramfs image**
```sh
setenv ipaddr 192.168.1.1
setenv serverip 192.168.1.2
tftpboot 0x46000000 openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-initramfs-kernel.bin
fdt addr $(fdtcontroladdr)
fdt rm /signature
bootm
```
**4. Flash sysupgrade image**
Place the sysupgrade image in `/tmp`, then run:
```sh
sysupgrade /tmp/openwrt-mediatek-filogic-jiorouter_ax6000-jidu6101-squashfs-sysupgrade.bin
```
Alternatively, use the sysupgrade option in LuCI.
Note:
- The raw MTD u-boot-env partition is only used for MAC address storage, while the active U-Boot environment is stored in the UBI volume.
- These devices ship with secure boot enabled and stock U-Boot only accepts vendor-signed FIT images.
- BL2/FIP cannot be replaced, so the stock signature verification path cannot be disabled directly.
- Setting ipaddr='' forces U-Boot to exit the web failsafe path and continue into autoboot.
- The custom bootcmd loads OpenWrt from the UBI volume and removes the /signature node before bootm, allowing unsigned OpenWrt FIT images to boot.
- Stock U-Boot expects its environment in a UBI volume named u-boot-env, so it is created during initial setup.
Signed-off-by: sh3ikh-faisal <sheikhfaisal713@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22201
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
In case OpenWrt is used to build a custom distribution, the default
button handling logic may be undesired.
Add config options to disable default standard button handling code
at build-time.
Signed-off-by: David Bauer <mail@david-bauer.net>
In case OpenWrt is used to build a custom distribution, the default
button handling logic may be undesired.
Add config options to disable default standard button handling code
at build-time.
Signed-off-by: David Bauer <mail@david-bauer.net>
Add support for Xiaomi AX5400 (RA74).
Specifications:
* SoC: Qualcomm IPQ5018 (64-bit dual-core ARM Cortex-A53 @ 1.0Ghz)
* Memory: Etrontech EM6HE16EWAKG 512 MiB DDR3L-933
* Serial Port: 1v8 TTL 115200n8
* Wi-Fi: IPQ5018 (2x2 2.4 Ghz 802.11b/g/n/ax - up to 574 Mbps)
QCN9024 (4x4 5 Ghz 802.11an/ac/ax - up to 4804 Mbps)
* Ethernet: IPQ5018 integrated virtual switch connected to an
external QCA8337 switch (3 LAN Ports 10/100/1000)
* Flash: Gigadevice GD5F1GQ5REYIG (128 MiB)
* LEDs: 1x System Blue (GPIO 24 Active High)
1x System Yellow (GPIO 25 Active High)
1x WAN Link Blue (GPIO 26 Active High)
1x WAN Link Yellow (GPIO 27 Active High)
* Buttons: 1x Reset (GPIO 38 Active Low)
1x WPS (GPIO 28 Active Low)
* MAC address layout: LAN (eth1): 0:art @ offset 0x0
WAN (eth0): 0:art @ offset 0x6
Flash instructions: (use redmi-ax5400 image for the Redmi AX5400)
Download XMIR Patcher: https://github.com/openwrt-xiaomi/xmir-patcher
First flash a ubinized OpenWrt initramfs that will serve as the intermediate step, since
OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for
packages, through either of the below two methods:
Installation via XMIR Patcher:
1. Load the initramfs image: openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi
Installation via ubiformat method, through SSH:
1. If needed, enable SSH using XMIR Patcher.
2. Copy the file openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi to the /tmp directory
3. Open an SSH shell to the router
4. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1):
nvram get flag_boot_rootfs
5. Find the rootfs and rootfs_1 mtd indexes respectively:
cat /proc/mtd
Please confirm if mtd18 and mtd19 are the correct indexes from above!
6. Use the command ubiformat to flash the opposite mtd with UBI image:
If nvram get flag_boot_rootfs returned 0:
ubiformat /dev/mtd19 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit
otherwise:
ubiformat /dev/mtd18 -y -f /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit
7. Reboot the device by:
reboot
Continue in order to pernamently flash OpenWrt:
1. Upload the sysupgrade image to /tmp/ using SCP:
scp -O <path to image> root@192.168.1.1:/tmp/
2. Open an SSH shell to 192.168.1.1 from a PC within the same subnet
3. Use sysupgrade to flash the sysupgrade image:
sysupgrade -n -v /tmp/openwrt-qualcommax-ipq50xx-xiaomi_redmi-ax5400-squashfs-sysupgrade.bin
Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired.
Signed-off-by: George Moussalem <george.moussalem@outlook.com>
Link: https://github.com/openwrt/openwrt/pull/23374
Signed-off-by: Robert Marko <robimarko@gmail.com>
OSLEC has been dropped upstream since Linux 6.16.
Reflect that by no longer providing the kernel module package
`kmod-echo` which essentially became an empty stub.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Currently, there is no SBOM generation in imagebuilder when the package
system 'apk' is used. This commit adds this feature back. This already
worked for the package system 'opkg'.
Furthermore, generating the SBOM using perl is not reproducible if the
input data has not changed. A different file is always generated. This is
not the case with Python. For this reason, Python is now used to generate
the SBOM for the imagebuilder.
The script has already been prepared so that it can also process the opkg
package system for generating the SBOM.
Signed-off-by: Florian Eckert <fe@dev.tdt.de>
This commit adds support for the netis MEX605, which is a variant based on the netis NX30 V2.
1. Update brand naming from Netis to netis to follow the official branding.
2. Rename NX30V2 to NX30 V2 to correctly reflect it as the second version of the NX30.
3. Update variant notation for consistency.
cherry picked from commit c982357
1. Add 'model' to the DTS for netis NX30 V2 and define WiFi LED.
4. Fix typo.
Signed-off-by: Zhiwei Cao <bfdeh@126.com>
Signed-off-by: David Han <h96643864@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22726
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This improves on openwrt/openwrt@aeb9028aab by adding support for
other Dell EMC Edge620/640/680 devices and mapping
the interfaces to match the markings on the device.
This modifies the netdevices.mk file to set the boot flag for
ixgbe driver to load it in early stage of the boot process to
allow for proper mapping of the network interface PCI paths
inside the 02_network script. This will also allow other devices
using the ixgbe driver to do proper mapping in 02_network script.
The 02_network script is then modified to support all
dell-emc-620/640/680 devices. It now maps the network
interfaces via PCI paths to match the markings on the device.
The interface marked GE6 is still used for WAN with
interfaces GE1-GE5 used for LAN.
The SFP1 and SFP2 interfaces are left to be assigned by
the user.
Signed-off-by: Raylynn Knight <rayknight@me.com>
Link: https://github.com/openwrt/openwrt/pull/23110
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Ethernet LAN port is set to `eth1` (silkscreen "ETH2" and case label "2") next to the 2x USB Type-A
ports and WAN is set to `eth0` (silkscreen "ETH1" and case label "1") next to the USB Type-C port.
The USER ("reset") button serves as the reset button. A short press will reboot and a long press
will reset to factory settings (deleting all data) if using squashfs image.
MASK ("maskrom") and RCRY ("recovery") buttons are enabled but are not set to any specific function
Pressing the POWER button will `poweroff` the device and it will stay off until a power cycle.
Hardware
---------------
* SoC: RockChip RK3576 64-bit ARMv8-A 8 cores big.LITTLE (4x A72 and 4x A53)
* RAM: 3/4GB LPDDR4X or 8/16GB LPDDR5
* Ethernet: 2x GbE (SoC RGMII MAC, RTL8211F PHY)
* 3x LEDs (SYS - red / 1 (WAN) - green / 2 (LAN) - green)
* 4x Buttons (MASK ("maskrom"), RCRY ("recovery"), USER ("reset" - OpenWrt reset), POWER)
* 1x 16MiB SPI NOR on board
* 1x UFS slot for optional UFS 2.0 module (currently not supported)
* 1x microSD card slot (UHS-I)
* 1x HDMI OUT
* 1x Headphone OUT 3.5mm
* 1x M.2 M-key 2280 PCIe slot (PCIe 2.1 x1 supports NVMe SSD)
* 1x M.2 E-key *SDIO* slot for optional RTL8822CS Wi-Fi 5
* the case has integrated antennae as well as 2x knockouts
* the device tree is missing the nodes relevant to Wi-Fi operations so it's not supported for now.
* 2x USB 3.2 Gen 1 Type-A Ports
* Power: 1x USB Type-C 6V-20V with both DC and USB PD supported
* Serial: 1500000 8N1 3.3V - 2.54mm 3-pin header next to HDMI
MAC addresses
---------------
WAN (`eth0` case label "1"): generated from /sys/.../mmcblk0/cid (CID of SD card)
LAN (`eth1` case label "2"): WAN + 1
Installation
---------------
Decompress the archive of the OpenWrt sysupgrade image and write it to a microSD card using `dd`
or use Balena Etcher (no need to decompress).
Boot
---------------
Insert microSD card, set boot switch to "UFS/SD" and then supply power.
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Apply pending U-Boot patches so that Rockchip RK3576 devices can boot from SD card. The problem:
"The BootROM on RK3576 has an issue loading boot images from an SD-card. This issue can be worked
around by injecting an initial boot image before TPL…and return to BootROM to load next image, TPL"
Compilation of the initial boot image has been added to the U-Boot build recipe.
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Select `CONFIG_ROCKCHIP_SARADC=y` to enable Rockchip SAR ADC
Add ADC Ladder Buttons driver as a kernel module as well as `kmod-button-hotplug` to the list of
default packages for Rockchip targets that have buttons connected to ADC, not including some
devices (e.g. NanoPi R76S) that have ADC buttons which are not in the device tree.
This is needed to use buttons on Rockchip devices that are connected to ADC and not GPIO
Tested on FriendlyELEC NanoPi M5
Signed-off-by: Ryan Leung <untilscour@protonmail.com>
Link: https://github.com/openwrt/openwrt/pull/23008
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The current 150s watchdog timeout is too aggressive, leading to
premature hostname re-resolution on alive connections.
Even with a 25s keepalive, handshakes may not occur within the 150s window.
Increasing the timeout to 180s aligns the watchdog with WireGuard's
REJECT_AFTER_TIME constant, ensuring we only re-resolve when the connection
is truly considered dead.
Signed-off-by: Roberto Almeida Silva <robertoalmeidasilva1981@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/23248
Signed-off-by: Robert Marko <robimarko@gmail.com>
The vendor firmware checks for a bmt header in the last 528 erase blocks
of flash. The OpenWrt partition table did not respect that requirement,
and therefore the vendor and openwrt chainloader fight over those blocks
on every boot, potentially corrupting data stored in UBI blocks there.
This commit increases the size of the reserved_bmt partition to avoid
that fight.
Although the vendor bootloader only seems to touch the final 250 erase
blocks[1], the original vendor firmware system partition ended at
0x1be00000[2], so to be conservative, the consensus is to use that as
the end of mtd2 (ubi) partition and leave the last 528 blocks for mtd3
(reserved_bmt).
From https://openwrt.org/toh/gemtek/mxf-w1700k:
[1] OEM bootlog: [ 5.324337] bmt pool size: 250
[2] OEM bootlog: [ 5.478927] 0x000008600000-0x00001be00000 : "system"
Adds a compat_version to warn users to re-install to accomodate the
shrunken mtd2 ubi partition.
Fixed two nits suggested by Claude, zero padding a hex value and removed
an extra space.
Removed the wildcard setting of compat_version for other boards, as
suggested by Robert Marko, set compat_version only for the w1700k.
Reported-by: Loïc Yhuel <loic.yhuel@gmail.com>
Signed-off-by: Russell Senior <russell@personaltelco.net>
Link: https://github.com/openwrt/openwrt/pull/23061
Signed-off-by: Robert Marko <robimarko@gmail.com>
895f92164b66 uloop: add ULOOP_PRIORITY support for EPOLLPRI events
f9b1f3ff17ba uloop: revert my flag changes from the ULOOP_PRIORITY change
2982bfb1c325 blob: fix wrong type for realloc result in blob_buffer_grow()
78c20f6c8579 json_script: convert recursive __json_script_file_free() to iterative
e7c13bf8cbca usock: fix off-by-one in nanosecond normalization in poll_restart()
68b3f1588de4 uloop: usock: add error checking for fcntl and remove duplicate include
03821f942c49 uloop: fix undefined behavior in signal bit operations for signals > 32
e6e6fd83e26d blobmsg: fix policy name length overflow and add bounds check in blobmsg_parse()
d30b9cc1a02d usock: fix integer overflow in timeout calculations
406e342bb900 udebug: fix double off-by-one in udebug_entry_vprintf()
700eca0bac66 blobmsg_json: fix integer overflow in blobmsg_puts()
6351fe552162 blobmsg_json: floor strbuf size and tighten the post-format guard
58b6543f1b25 blobmsg: fix unsigned integer overflow in blobmsg_alloc_string_buffer()
d7a3ae699df0 blobmsg: use correct byte-order macro when setting BLOB_ATTR_EXTENDED
23c6618a5b90 blobmsg_json: fix double format string to avoid truncation and data loss
1edf1d704e76 jshn: fix integer overflow and type confusion in jshn_parse_file
9b488010c4a7 utils: fix integer overflow in __calloc_a()
40a87f734b94 blob: fix integer overflow in buffer growth functions
02fccb465651 blob: use size_t for blob_memdup() length
0fa612ca08f7 json_script: avoid alloca() on attacker-controlled pattern length
8c9862b6921b blobmsg: fix integer overflow in blobmsg_realloc_string_buffer()
5fbef5bb94fb ustream: avoid INT_MAX overflow on malloc in ustream_vprintf()
1501e60e5554 md5: detect read errors in md5sum() instead of returning a bogus hash
Link: https://github.com/openwrt/openwrt/pull/23212
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
kmod-sound-midi2 expects sound/core/snd-ump.ko, but
CONFIG_SND_UMP=y builds it in-kernel rather than as
a module. Replace the forced built-in setting with
plain CONFIG_SND_UMP so the module can be packaged
correctly.
Signed-off-by: Mieczyslaw Nalewaj <namiltd@yahoo.com>
Link: https://github.com/openwrt/openwrt/pull/23265
Signed-off-by: Robert Marko <robimarko@gmail.com>
This commit adds support for Qihoo 360T7 (UBI layout).
Aims
----
1. +20 MB additional free space for the packages
2. More reliable storage for the factory and fip partitions (in UBI)
Install (from non-UBI OpenWrt)
------------------------------
1. Navigate http://192.168.1.1/ and download mtd backups
2. Upgrade OpenWrt with installer initramfs image (force upgrade, don't
keep settings). Wait until OpenWrt reboots and until installer:
- Prepare new factory partition
- Format new ubi
- Make ubi volumes
- Write new fip and bl2
3. Navigate http://192.168.1.1/ and Upgrade with OpenWrt 'sysupgrade.bin'
image (don't keep settings)
Installer
---------
Based on OpenWrt UBI Installer Image Generator for Linksys E8450 and
Belkin RT3200
Link: https://github.com/dangowrt/owrt-ubi-installer
Ready installer image
Link: https://github.com/csharper2005/owrt-ubi-installer/tree/qihoo/bin
Installer script
Link: https://github.com/csharper2005/owrt-ubi-installer/blob/qihoo/files/
installer/install.sh
Committing to the parent Daniel's repository is not yet possible because
there are no official images and imagebuilder for Qihoo 360T7 (UBI) yet.
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22797
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
This commit adds U-Boot for Qihoo 360T7 (UBI layout).
Aims:
1. +20 MB additional free space for the packages;
2. More reliable storage for the factory and fip partitions (in UBI).
Signed-off-by: Mikhail Zhilkin <csharper2005@gmail.com>
Link: https://github.com/openwrt/openwrt/pull/22797
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
The Allwinner T113-s3 (sun8i) SoC features a dual-core Cortex-A7 ARM CPU and
128MB of DDR3 memory in the same physical package. It supports industrial
temperature ranges. Most of the IP blocks are shared with the D1/D1s core.
There are multiple variants of the SoC, which may vary in the included memory
size, with some of them including a C906 RISC-V co-processor.
Boards supported:
- MangoPi MQDual T113
- wireless-only (RTL8723DS)
- MYIR MYD-YT113 eMMC
- 1Gbit ethernet (Motorcomm YT8531 PHY)
- 4GByte eMMC
- M.2-type slot for 4G/5G cards, plus 2x SIM slot
- USB 2.0 ports
- GPIO/I2C/SPI/CAN ports
- FNLink 6131 (rtl8733bu) wifi module
- MYIR MYD-YT113 SPI
- Same as above but with 256Mbyte SPI-NAND flash instead of eMMC
- Rongpin RP-T113
- 100Mbit ethernet (ICplus IP101GR PHY)
- miniPCIe slot for 4G cards, plus 1x SIM slot
- 3x USB 2.0 ports
- RTL8723BS wireless
- HYM8563 RTC
- GPIO/I2C/SPI/CAN ports
- Olimex T113-Olinuxino
- 100Mbit ethernet (ICplus IP101GR)
- UEXT connector (GPIO/I2C/SPI ports)
- 1x USB 2.0
- audio jack, LEDC
Installation:
Use the standard sunxi installation to an SD-card.
Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
rebuilding x86 did fail in an existing build directory
mkdir fails if the folder exists already
Signed-off-by: Sander Schutten <schutten@hotmail.com>
Signed-off-by: Florian Maurer <fmaurer@disroot.org>
The ucode migration wrote "basic_rate" into the wpa_supplicant network
block, but that is not a valid wpa_supplicant network field, causing:
Line 15: unknown network field 'basic_rate'.
failed to parse network block.
Map UCI basic_rate to the correct wpa_supplicant fields, matching the
behavior of the legacy shell script (hostapd.sh):
- mesh mode: mesh_basic_rates (space-separated, 100 kb/s units)
- sta/adhoc: rates (comma-separated Mbps)
Link: https://github.com/openwrt/openwrt/commit/a854d833eabdbc3b42065927c136d75b981a1021
Signed-off-by: Florian Maurer <f.maurer@outlook.de>
[fix commit message link]
Signed-off-by: David Bauer <mail@david-bauer.net>
John Crispin
Robert Marko
Shiji Yang
Daniel Golle
Balázs Triszka
Andy Chiang
David Bauer
Jonas Jelonek
Fil Dunsky
sh3ikh-faisal
Thomas Weißschuh
George Moussalem
Robert Marko
Ryan Leung
Andrii Kuiukoff
Florian Eckert
Hauke Mehrtens
Stefan Kalscheuer
David Han
Raylynn Knight
Qingfang Deng
Mikhail Zhilkin
Hannu Nyman
Roberto Almeida Silva
Russell Senior
Paul Spooren
Mieczyslaw Nalewaj
Zoltan HERPAI
Til Kaiser
Wei-Ting Yang
Sander Schutten
Florian Maurer
Michael Pfeifroth